Nilfisk-Advance BW4-P Manual Download Page 18

Page: 18 / 20

110007944-EN
Software Manual_Pegasus.

6.3 Upgrade Inverter

Power off unit using service switch (wait for unit to discharge approximately 5 min.)

Open Inverter box

Disconnect the Display cable connected to either of the two modbus terminals

Connect the usb cable (110007946) to either one of the modbus connectors

Connect usb cable to PC

Power on inverter by using service switch (AWARE OF HIGH VOLTAGE IN INVERTER!)

Start up Firmware upgrade program (Can be downloaded from Nilfisk FOOD web)

Click browse to select upgrade file *.hex (Can be downloaded from Nilfisk FOOD web)

Click in Serial port up/down to select the com port for USB cable, if comport is not showing

press “refresh” button

10. If necessary change inverter ID to match Inverter ID, Default is 1

11.

Press Upload Firmware, and wait for progress bar to reach the end and turn green

12.

The progress bar will start moving

Summary of Contents for BW4-P




















Search results

Summary of Contents for BW4-P

Reviews:

Related manuals for BW4-P

Brands by name

Popular brands

Nilfisk-Advance BW4-P, Manual

Search results

Summary of Contents for BW4-P

Reviews:

Related manuals for BW4-P

Brands by name

Popular brands