background image

20

W

A L L

M

O U N T E D

P

R O G R A M M A B L E

I R   K

E Y P A D

S

Y S T E M

Erasing a Single IR Command

If you make a mistake, you can erase just a sin-
gle key anytime by following these steps:

1. Press the PROGRAM button. The PROGRAM

LED, the IR/SEQ LED and the PAGE LED light
up red.

2. Press and hold the ERASE button until all the

PROMPT LEDs light up, then release. The PRO-
GRAM LED begins to flash, warning you that
you are about to erase. 

3. Select the Page, then the Key that corresponds

to the address of the IR command that you wish
to erase. 
This erases any IR code stored at that
address.

4. To exit the Program mode, press the PROGRAM

button (the PROGRAM LED will go out).

Building Sequences to Automate
Any System

Planning the Sequence 

Begin by writing down the address (Page, Key)
of the key which will trigger the sequence.
Sometimes, it helps to write a note describing
the function of the command. A sequence can
have a maximum of ten steps. See 

Figure 17

.

NOTE: The power command for the preampli-
fier/receiver is never manually programmed
into a sequence. The IntelliPad’s Auto Power
Insert feature is enabled via the jumper labeled
Status Feedback.

System
System

Tuner

Tape

CD

Tuner
Tuner

Play

Stop

Pause

Tuner Input

Preset Station

Tape Deck

CD Player

Figure 17
Planning a sequence

TRIGGER

1
2
3
4
5
6
7
8
9

10

PAGE

KEY

NOTES

NUMBER

DS00154A/IntelliPad  2/5/99 4:32 PM  Page 20

Summary of Contents for IntelliPad
































Reviews: