Nikon AF-S DX Zoom Nikkor 18-135/3.5-5.6G ED Repair Manual Download Page 33

Page: 33 / 98

JAA79651-R.3695.A

- Ａ・AF-S DX 8-35/3.5-5.6G -

・

Fit the convex portion of the segment gear ring in the concave portion of the SWM base unit, and assemble

them. Then rotate the segment gear ring in the direction of the arrow.

Segment gear ring

Grease: I-40

Magnetic tape surface

Caution: Do not touch the magnetic surface directly with hand/tool.

Convex

portion

Concave portion

Apply to the sliding surface with
the segment gear ring.

Apply to SWM base unit and
sliding surfaces

SWM base unit

Torque rubber

Adhesive: C-8008B

Grease: GP-1RS

Apply to over all groove ×3.

Segment gear ring

Summary of Contents for AF-S DX Zoom Nikkor 18-135/3.5-5.6G ED



































































































Search results

Summary of Contents for AF-S DX Zoom Nikkor 18-135/3.5-5.6G ED

Reviews:

Related manuals for AF-S DX Zoom Nikkor 18-135/3.5-5.6G ED

Brands by name

Popular brands

Nikon AF-S DX Zoom Nikkor 18-135/3.5-5.6G ED, Repair Manual

Search results

Summary of Contents for AF-S DX Zoom Nikkor 18-135/3.5-5.6G ED

Reviews:

Related manuals for AF-S DX Zoom Nikkor 18-135/3.5-5.6G ED

Brands by name

Popular brands