Nikon AF-S DX Zoom Nikkor 18-135/3.5-5.6G ED Repair Manual Download Page 14

Page: 14 / 98

JAA79651-R.3695.A

- Ｄ・AF-S DX 8-35/3.5-5.6G -

Focus sliding tube

・

Rotate the focus sliding tube in the direction of the arrow, and remove it.

・

Rotate the filter ring and cover ring, and extend the inner-

fixed tube unit.

・

Take out three screws (#84), and remove the inner-fixed

tube unit from the 1st lens-G sliding tube unit.

Focus sliding tube

Inner-fixed tube unit

#84

Filter ring

Cover ring

Inner-fixed tube unit

Separation of 1st lens-G sliding tube unit from Inner-fixed tube unit

1st lens-G sliding
tube unit

Summary of Contents for AF-S DX Zoom Nikkor 18-135/3.5-5.6G ED



































































































Search results

Summary of Contents for AF-S DX Zoom Nikkor 18-135/3.5-5.6G ED

Reviews:

Related manuals for AF-S DX Zoom Nikkor 18-135/3.5-5.6G ED

Brands by name

Popular brands

Nikon AF-S DX Zoom Nikkor 18-135/3.5-5.6G ED, Repair Manual

Search results

Summary of Contents for AF-S DX Zoom Nikkor 18-135/3.5-5.6G ED

Reviews:

Related manuals for AF-S DX Zoom Nikkor 18-135/3.5-5.6G ED

Brands by name

Popular brands