Bayco Products, Inc. • 640 South Sanden Blvd. • Wylie, TX 75098 • 1-800-233-2155 • 1-469-326-9400 • www.nightstick.com
INS-XPR-5572GA/RA-16
07-23-2018
NOTE: If the charger is being installed onto a wooden surface, drill a 3/32” pilot
hole in all 4 locations.
y
The mounting screw holes can be accessed from the front of the charger when the
Angle Light is not installed in the charger.
y
Looking through the mounting holes in the front face of the charger, line up the
mounting holes for the charger with the pilot holes (or drywall anchors) and one at a
time, carefully insert each of the supplied #8 x 32 x 1 ½” Pan Head Screws into the
mounting holes from the front of the charger. Give each screw a small turn by hand to
get each one started.
y
Using a #2 Phillips Head Screwdriver, hand-tighten each screw until the charger is
securely affi xed to the mounting surface.
CAUTION:
Do not use an electric drill or drill
driver to install the screws. Do not over-tighten. Doing so could damage the mounting
holes in the charger.
y
Plug either the Nightstick AC or DC Power Supply cord into the power port on the
bottom of the 5572-CHGR1 charger and then into the appropriate power outlet.
y
The LED Charge Indicator Light on the charger will momentarily light up GREEN and
then turn RED and then go off. This is normal behavior when the Angle Light is NOT
installed in the charger.
y
The charger is now ready to use.
POWERING THE XPR-5572
The XPR-5572 Intrinsically Safe Permissible Rechargeable Angle Light can be
powered in one of two ways:
y
The Nightstick 5572-BATT Lithium-ion Rechargeable Battery Pack.
y
The Nightstick 5570-BATT Non-Rechargeable Battery Carrier and 6 - AA
Energizer
EN91
or
Energizer E91
Batteries.
WARNING: Do not use any other type of non-rechargeable battery with this light.
WARNING: Do not use rechargeable AA batteries with this light.
5572-BATT LITHIUM-ION RECHARGEABLE BATTERY PACK
Image 1
Image 2
Image 3
WARNING: The Nightstick 5572-BATT Lithium-ion Rechargeable Battery Pack is
a proprietary shape and design and will only fi t in the XPP-5570R or XPR-5572R
Angle Lights. Do not attempt to use this battery pack in any other light. Do not
attempt to use any other rechargeable battery pack in this light.
WARNING: The Nightstick 5572-BATT Lithium-ion Rechargeable Battery Pack is a
sealed unit and is not designed to be opened up. Do not attempt to open the 5572-
BATT Lithium-ion Rechargeable Battery Pack.
y
To install the 5572-BATT Lithium-ion Rechargeable
Battery Pack, unscrew the Torx Head Screw located on
the Battery Compartment Door on the base of the light
using the included Torx Wrench. (Image 1)
NOTE: The Battery Compartment Door Torx Screw
utilizes a design that prevents the screw from falling
out of the door. Do not attempt to remove the screw.
(Image 2)
y
With the Battery Compartment Door opened enough
to provide clearance, insert the 5572-BATT Lithium-ion
Rechargeable Battery Pack with the end having the metal
contacts on it being inserted fi rst and the rails on the
bottom of the Battery Pack positioned toward the back of
the light. (Image 3)
y
With the 5572-BATT Lithium-ion Rechargeable Battery Pack fully inserted into the
handle of the light, close the Battery Compartment Door and secure it in place with the
Battery Compartment Door Torx Head Screw and the included Torx Wrench. (Image 4)
WARNING: Do not over-tighten the Battery Compartment Door Torx Head Screw.
The Angle Light is now ready to be powered using the Nightstick 5572-BATT Lithium-ion
Rechargeable Battery Pack.
5570-BATT NON-RECHARGEABLE BATTERY CARRIER
WARNING: The Nightstick 5570-BATT Non-Rechargeable Battery Carrier is a
proprietary shape and design and will only fi t in the XPP-5570 or XPR-5572 Angle
Lights. Do not attempt to use this battery pack in any other light. Do not attempt
to use any other battery pack in this light.
The Nightstick 5570-BATT Non-Rechargeable Battery Carrier is designed to fi t 6 AA
batteries. In order to maintain the XPR-5572’s Intrinsically Safe Permissible rating, the
only AA batteries certifi ed for use with this light are the
Energizer EN91
or
Energizer E91
.
Do not attempt to use any other brand or model of AA batteries with this light.
Do not attempt to use any type of rechargeable AA batteries with this light.
Installing or replacing the batteries
y
Begin by positioning the 5570-BATT Non-Rechargeable Battery Carrier with the
arrow pointing to the left. (Image 5)
y
Using the thumb and index fi nger, squeeze in on the two sides of the carrier cover
closest to the right end of the carrier. (Image 6)
y
This action will cause the tabs on the right end of the cover to release from the base
and allow the cover to simply lift away. (Image 7)
y
Using 6 – AA
Energizer EN91
or
Energizer E91
(make sure that all 6 batteries are of one or the other
model…do not use a combination of the two), install the
batteries per the diagram located on the inside base of the
battery carrier. (Image 8)
y
Take care not to bend any of the battery contact
springs, and to make sure that all 6 batteries are properly
seated before reinstalling the cover. (Image 9)
y
To reinstall the cover, insert the two tabs on the left-
hand end of the cover into the two corresponding slots on
the left end of base. (Image 10)
y
While keeping the left-hand tabs in their slots, gently
press down on the right side of the cover until the two right-
hand tabs slip into their respective slots. (Image 11)
NOTE: The battery carrier cover will only fi t one way. It is not possible to install it
in a reversed position.
The Nightstick 5570-BATT Non-Rechargeable Battery Carrier is ready to install into
the Angle Light. Installation of the 5570-BATT Non-Rechargeable Battery Carrier into the
Angle Light is the same as installing the 5572-BATT Lithium-ion Battery Pack. Please
see the instructions listed above in the
5572-BATT LITHIUM-ION RECHARGEABLE
BATTERY PACK
section.
PLACING THE ANGLE LIGHT INTO THE CHARGER
The Nightstick 5572-CHGR1 charger is designed to securely hold a properly installed
XPR-5572 Angle Light in place under conditions up to and including 9g of lateral force
meeting the requirements of NFPA 1901 (2009).
WARNING: Installing the Angle Light into the charger MUST be done using the
following steps. Failure to do so could damage the charger or its ability to hold
the Angle Light securely in place.
The spring-loaded grips located on the charger, are designed to snap around the
body of the light one at a time…not simultaneously.
y
While positioned in front of the charger, grasp the Angle Light around the bezel and
place either the left or right side of the light into the charger at an approximate 45
Image 4
Image 5
Image 6
Image 7
Image 8
Image 9
Image 10
Image 11
Image 12
Image 13
Image 14
