background image

14

NRX   -       -N    

 with CORONET reducer  ● For NRX □ -11K to 18K-C □ , follow the procedure on page 13.

When reassembly of the speed change and reduction sections is complete after disassembly, adjust pressure contact 

force according to the following procedure.

When reassembling the speed change section, move the ring to the low speed end (output shaft) in advance.

● Procedure

(1) Put a rod (T-wrench) etc. into the ER flange adjustment hole, and align the ER flange and adjuster surfaces on the same level by turning the 

adjuster. After that, assemble the main units of the speed reduction and change sections.

(2) Remove the top cover in the speed change section, look into the inside, and adjust pressure contact force by turning the adjuster with a rod (T-wrench) 

etc. according to the following procedure.

(3) Check pressure contact force adjustment according to the tables below. 

(Turning the adjuster clockwise increases contact force, and turning counterclockwise decreases contact force when viewed from the output shaft)

Adjuster fixing bolt

Adjuster

Cover

ER flange

Align the surfaces 

on the same level

Adjuster fixing bolt

Adjuster

Rod (T-wrench)

Casting hole

To increase 
contact force

To decrease 
contact force

ER flange

Cover

NRX □ -200B  to 2200-N □

Adjust by cam retainer backlash

NRX □ - 3700 to 7500-N □

Adjust by clearance between the cam disc and input cam

Model

Cam retainer backlash

200B/400B

750/1500

1°to 3°

2200

After adjusting to 1º to 3º, turn the adjuster by 

one pitch to increase contact force

Model

Clearance of the cam disc

3700 to 7500

After adjusting clearance to 0 to 0.1 mm, turn the 

adjuster by one pitch to increase contact force

(4) Hold the cam retainer with pliers, etc., and check that the total 

backlash is within the range of values in the table below.

If backlash is too large or small, turn the ER flange adjuster, and 

make adjustment.

(5) When shim (pressure contact force) adjustment is complete, secure the adjuster using the fixing bolt, and set the blind bolt on the other side.

Note : The fixing bolt is used to keep the adjuster from turning. Keep the tip of the bolt from coming into contact with the bottom of the adjuster.

(4) Look into the inside of the speed drive, and check that clearance 

between the cam disc and input cam is within the range of 

values in the table below.

If clearance is too large or small, turn the ER flange adjuster, 

and make adjustment.

Cam retainer

Input cam

Cam disc

Adjuster

ER flange

Blind bolt

Fixing bolt

Clearance

Clearance

Cam retainer

Cam retainer

Cam disc

1° to 3°

(6) Set the dial.

*Refer to the procedure for the standard NRX □ on page 12.

Summary of Contents for RINDCODE NRX Series





























Reviews: