background image

46

MAINTENANCE

Powerdrive MD2S Installation guide

4972 en - 2017.08 / d

7 - MAINTENANCE

•  All work relating to installation, commissioning 

and maintenance must be carried out by 

experienced, qualified personnel.

•  When a trip detected by the drive causes the motor to 

stop, fatal residual voltages remain on the terminals and 

in the drive. 

•  The drive stop function does not protect against high 

voltages on the terminal blocks.

•  Before carrying out any work on the drive or the motor, 

disconnect and padlock the isolating switch in the 

switchboard.

•  The  line  switch  integrated  as  an  option  in  the  drive 

does not isolate the drive input busbars. During the 

installation and maintenance phases, make sure that the 

power supply line is disrupted. 

•  When  the  drive  controls  a  permanent  magnet  motor, 

the isolating switch between the drive and the motor 

must be open to avoid the risk of motor voltage feedback. 

If there is no isolating switch, make sure the machine 

shaft is jammed to prevent it turning while work is carried 

out.

•  After  the  drive  is  switched  off,  the  external  control 

circuits can still be active and presents dangerous 

voltage. Check that these circuits are powered down 

before working on the control cables. 

•  Ensure  that  the  DC  bus  voltage  is  below  40V  before 

carrying out any work (the control board power-on 

indicator LED must be off). 

•  After the drive has been operated, keep away from the 

heatsink as it may be very hot (70°C).

•  After working on the motor, check that the phase order 

is correct when re-connecting the motor cables.

•  All protective covers must remain in place during tests.

•  Before  performing  high  voltage  tests  or  voltage 

withstand tests on the motor, switch off the drive and 

disconnect the motor.

There are very few maintenance and repair operations to be 

performed by the user on 

Powerdrive MD2S

 drives. Regular 

servicing operations are described below.

• 

Servicing

Printed circuits and drive components do not normally 

require any maintenance. Contact your vendor or the nearest 

approved repair company in the event of a problem.

CAUTION:

Do not dismantle the printed circuits while the drive 

is still under warranty, as this immediately makes the 

warranty null and void.

Do not touch the integrated circuits or the microprocessor 

with your fingers (ESD risk).

From time to time, with the drive powered down, check that 

the power connections are correctly tightened. The door 

filters must be checked and changed regularly depending on 

their state.

• 

Preventive maintenance

Device

Action

Frequency

Door filters 

(10µm)

Clean (1)

3 months

Replace

2 years

Power connections

Check 

tightness

1 year

Internal ventilation and in 

cabinet roof

Replace

5 years

Surge suppressor board

Replace

5 years

(1) Door filters are washable.

7.1 - Storage

The 

Powerdrive MD2S

 incorporates aluminium electrolytic 

capacitors.

If the drive has been stored for more than 12 months, it must 

therefore be switched on for 5 hrs at the rated operating 

voltage, and this operation must be repeated every 6 months.

If the drive has been stored for more than 36 months, the 

capacitors must be reformed.

This consists of gradually applying a DC voltage to the banks 

of capacitors, until voltage values close to the rated voltages 

are achieved, while ensuring that the dissipated power 

does not exceed the maximum values authorised by the 

manufacturer.

An instruction sheet is available - please contact your local 

technical support.

7.2 - Replacing products

CAUTION:

Products must be returned in their original packaging or 

in similar packaging, to prevent them being damaged. 

Otherwise, replacement under warranty could be refused.

Summary of Contents for Powerdrive MD2S





















































Reviews: