9
– English
EN
3.8 - Insights
3.8.1 - RADIO TEST FUNCTION
This feature allows for verifying the environmental RF noise level.
01.
Press the button
RADIO
TEST
: on the level LEDs a value appears that represents the
intensity of the ambient signal / RF noise, at 433.92 MHz
3.8.2 - DELETING THE PARAMETERS FROM THE MOTOR
This procedure clears all the parameters in the motor memory and restores the factory
settings.
01.
Hold down the button
RADIO
TEST
until the relative LED starts flashing; Lastly, release
the button.
02.
➔
The
green OK
LED flashes: (within 3 sec) press the
OK
button to confirm.
Note:
this procedure does not delete the transmitters. For this function see 3.4.3 - De-
leting all transmitters.
3.8.4 - CHECKING THE SOFTWARE VERSION
01.
Press the
OK
button
02.
➔
The
green OK
LED flashes: (within 3 sec) press the button
F1
F2
F3
.
03.
The level LEDs show the version and revision of the software.
04.
After 5 seconds TTPRO turns off automatically.
3.8.5 - UPDATING THE TTPRO FIRMWARE
01.
If you need to update TTPRO (eg. the product software upgrade), contact the
NICE technical support.
3.8.6 - CHANGING THE MOTOR ADDRESS
01.
Press the button
F1
F2
F3
: the actual motor address will start to flash on the level
LEDs.
02.
Use
Table 1
to select the new desired address.
03.
Use buttons
and
to select the address you want to assign.
04.
➔
The
green OK
LED flashes: (within 3 sec) press the
OK
button to confirm.
3.8.3 - COPYING PARAMETERS AND TRANSMITTERS
Using various buttons, you can read the parameters and the transmitters stored in the
motor and then save them in the TTPRO memory. Subsequently, this data can be tran-
sferred to other motors of the same type.
Step 1 - Reading
parameters in the memory of the first motor
Warning
- Before proceeding, delete the memory of the TTPRO with the procedure
explained in paragraph 3.8.3.1.
01.
Press the button
RADIO
TEST
.
02.
Press one or more buttons (
F1
F2
F3
/
F1
F2
F3
/
F1
F2
F3
), according to the data you want
to copy:
•
F1
F2
F3
reads the parameters related to the rotation direction and to the limit switches
•
F1
F2
F3
reads the parameters related to the sensors (wind and sun levels, etc.)
•
F1
F2
F3
reads the parameters related to the radio transmitters
03.
When TTPRO receives the data, the LED on the key flashes rapidly.
04.
➔
The
green OK
LED flashes: (within 3 sec) press the
OK
button to confirm.
Step 2 - Writing parameters in another motor
Note:
the procedure will only take effect if the motor is of the same type as the one in
which the parameters were read.
01.
Press the button
RADIO
TEST
.
02.
Press one or more buttons (
F1
F2
F3
/
F1
F2
F3
/
F1
F2
F3
), according to the data you want
to write:
•
F1
F2
F3
writes the parameters related to the rotation direction and to the limit switches
•
F1
F2
F3
writes the parameters related to the sensors (wind and sun levels, etc.)
•
F1
F2
F3
writes the parameters related to the radio transmitters
03.
When TTPRO transfers the data, the LED on the key flashes rapidly.
04.
➔
The
green OK
LED flashes: (within 3 sec) press the
OK
button to confirm.
3.8.3.1 - Deleting of the parameters stored in TTPRO
01.
Press the button
RADIO
TEST
.
02.
Press the following buttons in sequence:
F1
F2
F3
,
F1
F2
F3
,
F1
F2
F3
.
03.
➔
The
green OK
LED flashes: (within 3 sec) press the
OK
button to confirm.
