background image

   www.hysecurity.com       

7

1.8 

The installation of this product is not a “do-

it-yourself” project. A qualifi ed gate operator 

installation company should be contacted 

to install the gate operator to ensure a safe 

and reliable installation. Since many aspects 

of gate system installation are under the 

control of the installer, it is the responsibility 

of the property owner to ensure the installer 

is qualifi ed to carry out the installation in a 

safe and professional manner.

1.9 

Consult local government agencies for 

up-to-date rules and regulations as certain 

municipalities have established licensing, 

codes or regulations that regulate automated 

gate system design and installation.

2. 

General Safety Information

A gate operator is only a component in a gate 

system. The other parts of the gate system 

can include the gate, the external entrapment 

sensors, access controls, and vehicle detectors. 

To have a gate system that provides safety, 

security, and reliable operation it is essential these 

components operate together as a system. It is 

the responsibility of the system designer and/or 

installer to ensure any safety or operational issues 

have been addressed.

IMPORTANT SAFETY INSTRUCTIONS

1. 

READ AND FOLLOW ALL INSTRUCTIONS.

2. 

Never let children operate or play with gate 

controls. Keep the remote control away from 

children.

3. 

Always keep people and objects away from 

the gate. NO ONE SHOULD CROSS THE 

PATH OF THE MOVING GATE.

4. 

Test the gate operator monthly. The gate 

MUST reverse on contact with a rigid 

object or stop when an object activates the 

non-contact sensors. After adjusting the 

force or the limit of travel, retest the gate 

operator. Failure to adjust and retest the 

gate operator properly can increase the risk 

of injury or death.

5. 

Use the emergency release only when the 

gate is not moving.

6. 

KEEP GATES PROPERLY MAINTAINED. Read 

the user’s manual. Have a qualifi ed service 

person make repairs to gate hardware.

7. 

The entrance is for vehicles only. Pedestrians 

must use separate entrance.

8. 

SAVE THESE INSTRUCTIONS.

  WARNING

To reduce the risk of injury or death.

Summary of Contents for TITAN12L





































Reviews: