background image

4

4

The

Hyppo

ETL

Swing Gate Operator

is designed to handle a swing gate up to 10

feet in total length and 400 lbs .

Apollo Operators

 are available only through

qualified dealers with an outstanding reputation in the fence and gate industry.
These dealers will be able to recommend the proper equipment for particular
applications.

Apollo Operators

are 12 Volt DC (

Direct Current

) powered. If a elec-

trical battery charger is used a 12 Volt sealed battery (33 ampere hour minimum) is
recommended . If solar charging is used a 12 volt 105 ampere hour battery is rec-
ommended. There are several advantages with 12 Volt DC systems:



Low voltage virtually eliminates risk of electrical shock.



Battery powered operators can provide up to 500 operations in the event of
power outages.



The battery may be recharged with a trickle charger or by solar energy
(eliminating the need for costly trenching to remote entrances).

If a trickle charger is used and a standard electrical outlet is not readily available, a
licensed electrician will be required for proper electrical hook up.

The following table should be used as a guide for capacity of operation of operators
only, additional options may reduce the the daily usage.

Please note that the charge

capability of solar panels will vary with different geographical locations. All solar
panels and battery chargers are designed for use with a 12 volt battery.

                              Daily Cycles

1-10

1-20

1-40

1-60

1-80

80+

5 watt solar panel

*

10 watt solar panel

*

20 watt solar panel

(requires SG4 regulator)

*

30 watt solar panel

(requires SG4 regulator)

*

40 watt solar panel

(requires SG4 regulator)

*

1.5 amp battery charger

*

10 amp battery charger

*

Note: Double the amount of solar panels for Dual Operators.

APPLICATIONS

Summary of Contents for HYPPO DUALETL

























Reviews: