Nibe AXC 30 Installer Manual Download Page 70

Page: 70 / 84

24 23 22 21 20 19 18 17 16 15 14 13

AA25

External

BT50

AA5-X2

External blocking (optional)

A contact (NO) can be connected to AA5-X2:21-22 to
allow blocking of the cooling operation. When the con-
tact closes, cooling operation is blocked.

24 23 22 21 20 19 18 17 16 15 14 13

AA25

External

External blocking

AA5-X2

Caution

The relay outputs on the accessory board can
have a max load of 2A (230V) in total.

CONNECTION OF THE COOLING
CIRCULATION PUMP (EQ1-GP10)

Connect the circulation pump (GP10) to AA5-X9:6 (230V),
AA5-X9:5 (N) and X1:3 (PE)

AA5-X9

AA25-X1

External

AA25

GP10

Caution

The charge pump ((AA25-GP12) is connected
in the control module. See the control module’s
Installer Manual to connect the charge pump.

CONNECTION OF THE REVERSING VALVE
MOTOR (EQ1-QN12)

Connect the reversing valve, cooling (QN12) to AA5-X9:2
(signal), AA5-X9:1 (N) and AA5-X10:2 (230 V).

AA5-X9

AA5-X10

AA25

External

Black

Blue

Brown

QN12

DIP SWITCH

The DIP switch (S2) on the accessory board (AA5) must
be set as follows.

AXC 30 F-series | GB

Summary of Contents for AXC 30





















































































Search results

Summary of Contents for AXC 30

Reviews:

Related manuals for AXC 30

Brands by name

Popular brands

Nibe AXC 30, Installer Manual

Search results

Summary of Contents for AXC 30

Reviews:

Related manuals for AXC 30

Brands by name

Popular brands