Nibe AXC 30 Installer Manual Download Page 65

Page: 65 / 84

External blocking

A contact (NO) can be connected to AA5-X2:21-22 to
block the accessory. When the contact closes, the ac-
cessory is blocked.

24 23 22 21 20 19 18 17 16 15 14 13

AA25

External

External blocking

AA5-X2

External blocking, hot water circulation pump
(QZ1-GP11)

A contact (NO) can be connected to AA5-X2:15-16 to
block the hot water circulation pump. When the contact
closes, the hot water circulation pump is blocked.

24 23 22 21 20 19 18 17 16 15 14 13

AA25

External

AA5-X2

External blocking

Caution

The relay outputs on the accessory board can
have a max load of 2A (230V) in total.

CONNECTION OF THE HOT WATER
CIRCULATION PUMP (QZ1-GP11)

Connect the circulation pump (GP11) to AA5-X9:8 (230V),
AA5-X9:7 (N) and X1:3 (PE).

AA5-X9

AA25-X1

External

AA25

GP11

CONNECTION OF THE MIXER VALVE
(QZ1-FQ3)

Connect the mixing valve motor (FQ3) to AA5-X9:6
(230V, open), AA5-X9:5 (N) and AA5-X9:4 (230V, close).

AA25

External

AA5-X9

FQ3

Open

CONNECTION OF AUXILIARY RELAY FOR
ADDITIONAL HEAT IN TANK

Connect the auxiliary relay for switching the additional
heat on and off to AA5-X9:1 (N) and AA5-X9:2 (230V).

External auxiliary relay

Additional
Hot water

AA5-X9

Extra Hot Water

External auxiliary relay

AA25 External

DIP SWITCH

The DIP switch (S2) on the accessory board (AA5) must
be set as follows.

AXC 30 F-series | GB

Summary of Contents for AXC 30





















































































Search results

Summary of Contents for AXC 30

Reviews:

Related manuals for AXC 30

Brands by name

Popular brands

Nibe AXC 30, Installer Manual

Search results

Summary of Contents for AXC 30

Reviews:

Related manuals for AXC 30

Brands by name

Popular brands