background image

Important information

SAFETY INFORMATION

This manual describes installation and service proced-
ures for implementation by specialists.

The manual must be left with the customer.

This appliance can be used by children
aged from 8 years and above and persons
with reduced physical, sensory or mental
capabilities or lack of experience and
knowledge if they have been given super-
vision or instruction concerning use of the
appliance in a safe way and understand
the hazards involved. Children shall not
play with the appliance. Cleaning and user
maintenance shall not be made by children
without supervision.

This is an original manual. It may not be
translated without the approval of NIBE.

Rights to make any design or technical
modifications are reserved.

©NIBE 2021.

SYMBOLS

NOTE

This symbol indicates danger to person or ma-
chine .

Caution

This symbol indicates important information
about what you should consider when installing
or servicing the installation.

TIP

This symbol indicates tips on how to facilitate
using the product.

MARKING

The CE mark is obligatory for most products
sold in the EU, regardless of where they are
made.

CE

Classification of enclosure of electro-technical
equipment.

IP21

Danger to person or machine.

!

Read the Installer Manual.

AXC 30 S-series | GB

4

S

S-series

Summary of Contents for AXC 30





















































































Reviews: