Nexo NXAMP4X1 User Manual Download Page 123

Page: 123 / 140

NXWIN4 SOFTWARE FOR NXAMP FIRMWARE UPGRADE

Then choose the serial port connected to the NXAMP Powered TDcontroller (note: only the

detected and available serial ports appear in the list), and finally press the download

button. The following splash window should pop up on screen:

To upgrade the NXAMP (fitted with NXES104 or NXDT104 board) through the network,

choose the network port interface and select the network card connected to the NXAMP(s).

Select device that you want to upgrade (by default only units in “Download mode” will be

selected).

Begin the upgrade

You can now confirm the download in the splash screen. The Nxwin4 will detect the

connected NXAMP target, and then download the appropriate software. If a NXES104 or

NXDT104 is fitted and need to be upgraded, it will be automatically done as well.

WARNING! After the upgrade of the NXES104 or the NXDT104 card you will be

prompt to turn the NXAMP powered TDcontroller OFF and ON again in download mode

before proceeding to NXAMP firmware part update.

PAGE 123 OF 140

Summary of Contents for NXAMP4X1













































































































































Search results

Summary of Contents for NXAMP4X1

Reviews:

Related manuals for NXAMP4X1

Brands by name

Popular brands

Nexo NXAMP4X1, User Manual

Search results

Summary of Contents for NXAMP4X1

Reviews:

Related manuals for NXAMP4X1

Brands by name

Popular brands