background image

Start Up Guide 

Provide adequate distance between the 1936-R/2936-R Series Optical Power 
Meters and adjacent walls for ventilation purposes.  Approximately 2-inch 
spacing for all surfaces is adequate. 

1.8 

  Electrical Requirements 

Before attempting to power up the unit for the first time, the following 
precautions must be followed: 

 

 

 

 

 

 

Have a qualified electrician verify the wall socket that will be used is 
properly polarized and properly grounded.   

 

Set the mains selector tumbler to the voltage that matches the power outlet 
AC voltage. 

 

Verify the correct rated fuses are installed according to the fuse marking 
on the rear panel.  

1.9 

  Power Supplies 

AC power is supplied through the rear panel input power connector that 
provides in-line transient protection and RF filtering. The input power 
connector contains the fuses and the switch to select series or parallel 
connection of the transformer primaries for operation at 100VAC, 120VAC, 
220VAC or 240VAC. The product is shipped with the setting on 110V. 
Please make sure you select the right setting according to your AC voltage 
level. Also, please make sure you insert the right fuses. The product is 
shipped with a spare of fuses for the 220VAC/240VAC settings.  

 

CAUTION 

Permanent damage will occur to the power meter if the input 
power connector settings are at either 100 or 120VAC and 
applied power is above 180VAC RMS 

 

 

WARNING 

To avoid electrical shock hazard, connect the instrument to 
properly earth-grounded, 3-prong receptacles only.  Failure 
to observe this precaution can result in severe injury. 

Summary of Contents for 1936-R series



















Reviews: