New Rock Technologies NRP1000 User Manual Download Page 35

Page: 35 / 86

NRP1000 Series IP Phone User Manual

New Rock Technologies, Inc. 5-11

Name Description

Enable LLDP

Enables the LLDP function.

Package
Interval(1-3600)

Specifies the interval at which LLDP packets are sent, in seconds. The default value is
60.

Enable Learning
Function

Enables the LLDP Learn function. If enabled, the phone can automatically learn values
of the QoS, VLAN ID, and 802.1p from the switch. If the data is different from that of
the LLDP server, phone synchronizes its values with that of the switch.

Quality of Service(QOS) Settings

Enable DSCP

Enables DSCP.

SIP DSCP

Sets a value for SIP DSCP.

Audio RTP DSCP

Sets a value for Audio RTP DSCP.

WAN Port VLAN Settings

Enable WAN Port
VLAN

Enables VLAN of the WAN port.

WAN Port VLAN
ID

Sets a VLAN ID. The value ranges from 0- to 4095.

SIP 802.1p
Priority

Sets a value for SIP 802.1P priority. The value ranges from 0 to 7.

Audio 802.1p
Priority

Sets a value for the audio 802.1P priority. The value ranges from 0 to 7.

LAN Port VLAN Settings

LAN Port VLAN
Mode

Enables/Disables the Port VLAN function.
If enabled, you need to input a VLAN ID different from that of the WAN port.

LAN Port VLAN
ID

Sets a VLAN ID. The value ranges from 0 to 4095.

5.4.4 Service Port

You can set the Telnet/HTTP/RTP port in this page.

Figure 5-12 Service port setting interface

Summary of Contents for NRP1000























































































Search results

Summary of Contents for NRP1000

Reviews:

Related manuals for NRP1000

Brands by name

Popular brands

New Rock Technologies NRP1000, User Manual

Search results

Summary of Contents for NRP1000

Reviews:

Related manuals for NRP1000

Brands by name

Popular brands