background image

INTRODUCTION

BUSHING REPLACEMENT

Bushing removal

• Generally, bushings mounted under interference are re-

moved only when they need to be replaced.

• The removal can therefore be destructive. However,

be careful not to damage the part where the bushing is
mounted.

BAIL14SE00802AS

4

Installing bushings under interference

• The bushings used in Seeders not require the applica-

tion of glue for their installation.

• The ideal thing is to use a press. This way, an aligned

installation and with the necessary force is ensured.

• However, in field situations where a press is not avail-

able, observe the following precautions:

• Use a suitable tool

(2)

to guide the bushing

(3)

in its

installation.

• Apart from guiding the bushing, the tool prevents the

bushing from being directly hit with a hammer, which
would cause its deformation and may even impede its
installation, in addition to forcing the disposal of the
bushing.

• Use a hammer

(1)

o move the tool

(2)

and the bushing

(3)

• The part

(4)

in which the bushing is installed needs to

be lying on a flat, hard surface.

• Check the mounting depth of the bushings: usually, the

end of the bushing must face the surface of the part in
which it is installed; see indication

(5)

.

BAIL14SE00802AT

5

REPLACEMENT OF SEALS

NOTE:

The fundamental care in the installation of seals

consists in not to deform them. This requires the use of
appropriate tools

NOTE:

Once removed, the seals cannot be reinstalled:

replace them.

47918066 10/09/2015

18

Summary of Contents for PS2045
































Reviews: