background image

INTRODUCTION

Basic instructions

HITCH THE MACHINE ONTO THE TRACTOR

CAUTION

Transport hazard!
Always connect a safety chain between the machine and the implement. Only use a safety chain with
a strength rating equal to or greater than the gross weight of the implement.
Failure to comply could result in minor or moderate injury.

C0039A

CAUTION

Avoid injury!
Handle all parts carefully. Do not place your hands or fingers between parts. Use Personal Protec-
tive Equipment (PPE) as indicated in this manual, including protective goggles, gloves, and safety
footwear.
Failure to comply could result in minor or moderate injury.

C0145A

DANGER

Crushing hazard!
Do not stand or place any body part between the implement and a moving tractor. Stop the tractor
engine and set the parking brake before you attach cables and hoses.
Failure to comply will result in death or serious injury.

D0112A

Engage the drawbar to the tractor and leveling

The drawbar

(1)

is engaged to the tractor through the bar

(2)

, and to the lower lift arms.

BAIL14SE00810AV

1

The machine leveling is set and maintained by the height
adjusted in the lower lift arms of the tractor.
The correct machine leveling during planting is critical to
the performance and maintaining of the correct depth of
seed and fertilizer.
The machine leveling

(A)

is correct when the sides of the

frame and the drawbar

(1)

are flat (parallel) to the ground.

BAIL14SE00810AW

2

47918066 10/09/2015

12

Summary of Contents for PS2045
































Reviews: