New Holland 555912001 Service Manual Download Page 44

Page: 44 / 81

INTRODUCTION

Alarm

description

Alarm explanation

Prior-

ity

Activation

Time

Resetting

Time

A1207

Operation not
allowed

Transition channel
door cannot be
opened when the
engine is running or
the cutterhead speed
is not 0

White

“Transition channel
door open” button
is pressed while
cutterhead speed is
not 0 or engine is
running

0 s

Time-out

5 s

A2000 Drive Disabled

Transmission is
shifting gears. Wait
until the shift has
finished

Yellow

Trying to drive
forward OR reverse
AND trans shift is
ongoing

0 s

Trans shift not
ongoing OR not
trying to drive
forward OR
reverse

0 s

A2001 Drive Disabled

Parking brake is on.
Push the parking
brake button Off

Yellow

Trying to drive
forward OR reverse
AND parking brake
on

0 s

Parking brake
Off OR not trying
to drive forward
OR reverse

0 s

A2002

Ground drive
(Gnddrive)1
hydro oil
temperature high

The temperature
at the ground drive
hydrostatic motor
is too high. Clean
radiator OR slow
down

Yellow

Temperature >

105 °C

10 s

Temperature <

100 °C

3 s

A2003

GndDrive2 hydro
oil temperature
high

The temperature
at the ground drive
hydrostatic motor
is too high. Clean
radiator OR slow
down

Yellow

Temperature >

105 °C

10 s

Temperature <

100 °C

3 s

A2004

Ground drive
hydro oil
pressure low

The pressure in
the ground drive
hydrostatic system
is too low. Check oil
level

Red

Engine running AND
pressure <

5 bar

1 s

Engine not
running OR
pressure ≥

5 bar

0.5 s

A2005 Spout not home

The spout home
position sensor has
not been detected.
Bring spout to home
position manually

White

Spout auto home
position procedure
did not see the home
sensor

0 s

Time-out

3 s

A2006

Spout movement
disabled.

Spout movement
is disabled in road
mode. Set the
“safety-on-the-road
button” to field

White

Road mode active
AND one of the spout
movement switches
pressed

0 s

Field mode
active AND no
spout movement
switches pressed

0 s

A2007

Command-
Grip™

handle

(MFH) position
problem

Fix problem. Then
clear alarm by moving
the

CommandGrip™

handle completely
forward and reverse

White

CommandGrip™

handle forward,
reverse OR neutral
check failed

0 s

Command-
Grip™

handle

forward, reverse
AND neutral
check OK

0 s

A2008 Trailer not found

IntelliFill™

not

functioning, no trailer
in view. please take
over manually

White

(integrated in state
flow diagram. alarm
raises when:)
auto filling
AND trailer lost

3 s

Not auto filling
OR trailer not lost

0 s

A2009 Trailer almost full -

White

Transition from!
trailer_full to
trailer_full

0 s

3 s

48142788 28/04/2017

Summary of Contents for 555912001


















































































Search results

Summary of Contents for 555912001

Reviews:

Related manuals for 555912001

Brands by name

Popular brands

New Holland 555912001, Service Manual

Search results

Summary of Contents for 555912001

Reviews:

Related manuals for 555912001

Brands by name

Popular brands