New Buck Corporation 1127B User Manual Download Page 3

Page: 3 / 43

TABLE OF CONTENTS

Safety Information and Warnings ........................................................................... 3

Product Identification .............................................................................................. 6

Product Features ...................................................................................................... 7

Unpacking ............................................................................................................... 7

Installation ............................................................................................................... 9

Producing Adequate Ventilation (Fresh Air for Combustion and Ventilation) .... 13

Gas Connection ..................................................................................................... 17

Connecting to Gas Supply .................................................................................... 18

Gas Pressure Check………………………………………………………………20

Log Placement……………………………………………………………………21

Lighting Instructions ............................................................................................ 22

Flame Check .................................................................................................... 26-27

Inspecting Pilot ................................................................................................ 26-27

Burner Flame Pattern ....................................................................................... 26-27

Wiring Diagram .................................................................................................... 28

Cleaning and Maintenance .................................................................................... 30

Troubleshooting .................................................................................................... 32

Technical Service .................................................................................................. 29

Parts List & Blown up View ............................................................................ 36-40

Warranty ............................................................................................................... 41

Summary of Contents for 1127B












































Search results

Summary of Contents for 1127B

Reviews:

Related manuals for 1127B

Brands by name

Popular brands

New Buck Corporation 1127B, User Manual

Search results

Summary of Contents for 1127B

Reviews:

Related manuals for 1127B

Brands by name

Popular brands