New Buck Corporation 1127B User Manual Download Page 31 | Manualshive

Page: 31 / 43

background image

WARNING:

ELECTRICAL GROUNDING INSTRUCTION: THIS APPLIANCE

IS EQUIPPED WITH A THREE-PRONG (GROUNDING) PLUG FOR YOUR
PROTECTION AGAINST SHOCK HAZARD AND SHOULD BE PLUGGED
DIRECTLY INTO A PROPERLY GROUNDED THREE-PRONG RECEPTACLE.

NOTE:

#PE A24001 Blower Motor

Rating: 120 volts/60MZ/0.54 Amps. 1 P.H.

Blower Motor is standard on all Model 1127B. See page 38 for blower motor location.

NOTE:

For convenience, allow licensed electrician to properly install a grounded 3-plug

receptacle near the unit.

SERVICING

Repair and replacement work should only be performed by a qualified service technician.

Always shut off the gas supply and make sure heater is cool before beginning any service
operation. Check for gas leaks after servicing.

REPAIR PARTS

A parts list with exploded view follows. Always include correct name, part number, and model
number of the heater when ordering service parts. Please contact your local dealer or distributor
when ordering. If one is not available, you may contact:

New Buck Corporation

8000

Highway

226

South

Spruce Pine, NC 28777

828-765-6144

29

«
...
29
30
31
32
33
...
»

Summary of Contents for 1127B












































Reviews:

No comments

Related manuals for 1127B

Brand: Watlow Electric Pages: 2

Brand: NARVI Pages: 12

Brand: Radiant Pages: 8

Brand: Radialight Pages: 80

Brand: Radialight Pages: 80

Brand: Zibro Pages: 16

Brand: Zibro Pages: 17

Brand: WMT Pages: 7

Brand: Olimpia splendid Pages: 8

Optimum Radiant Heater KRH600

Brand: Kambrook Pages: 12

Brand: Nibe Pages: 20

Brand: Qlima Pages: 45

Brand: INNOLIVING Pages: 14

Brand: Bock Water heaters Pages: 62

Brand: Zibro Pages: 14

Brand: Salda Pages: 12

Brand: Flama Pages: 32

RESIDENTIAL GAS FIRED WATER HEATERS

Brand: Giant Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands