manualshive.com logo in svg

Network Technologies Incorporated ENVIROMUX E-BCN-R, Installation Manual, Page: 11 / 13

Share
Download
Network Technologies Incorporated ENVIROMUX E-BCN-R Installation Manual Download Page 11

NTI ENVIROMUX SENSOR INSTALLATION 

 

10

BEACON and SIREN Connections 

 

Terminals have been provided for connection of a beacon (E-BCN-R(L)) and siren (E-SRN-M, E-BEEP1, etc) to use for visual 
alerts and audible alerts when configured.  Devices such as this can be installed in locations best suited to get attention.  All 
devices must be installed using 16-26 AWG wire.  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 Figure 11- Connect visual and audible external indicators 

 
 

For a complete listing of available sensors and accessories go to the product page for ENVIROMUX Enterprise Environment 
Monitoring Systems at 

http://www.networktechinc.com/enviro-monitor.html 

,   and at   

http://www.networktechinc.com/enviro-

mini.html

  for the E-MINI-LXO.  Manuals for each product covering installation and configuration for all features can also be found 

at these websites.     

 

Summary of Contents for ENVIROMUX E-BCN-R














Reviews:

No comments