manualshive.com logo in svg

Netio PowerDIN 4PZ, Manual, Page: 17 / 80

Share
Download
Netio PowerDIN 4PZ Manual Download Page 17

 

17 

 

Figure 13 – NETIO Discover web interface 

 

To successfully discover the IP address, the controlling system must be in the same LAN as the 
NETIO device.  

If the discovered IP address belongs to a different address range than that of your WiFi network, we 
recommend resetting the device to factory defaults (see chapter 

Restoring factory defaults

) and 

then configuring it according to chapter 

Configuration and control

. 

 

 

Figure 14 – Discovering and configuring network parameters using NETIO Discover 

 

To change the IP address, click the value in the MAC address column, uncheck Enable DHCP and 
specify the IP address, Subnet mask and Default gateway. After applying the settings, NETIO device 
will be accessible at the specified address. 

Enter the IP address into a web browser or the NETIO Mobile app and log in to the device. 

 

Note:  For MAC or Linux users use the NETIO Discover Multiplatform version. 

Summary of Contents for PowerDIN 4PZ

















































































Reviews:

No comments