NETGEAR RangeMax DGN3500 User Manual Download Page 58

Page: 58 / 125

Chapter 4: Managing Your Network

N300 Wireless Gigabit ADSL2+ Modem Router DGN3500 User Manual

Statistics

To view statistics, on the Router Status screen, click

Show Statistics

Figure 31.

The following table describes the wireless modem router statistics.

•

To change the polling frequency, enter a time in seconds in the

Poll Interval

field, and

click

Set Interval

•

To stop the polling, click

Stop

Item

Description

System Up Time

The time elapsed since the wireless modem router was last restarted.

Port

The statistics for the WAN (Internet) and LAN (Ethernet) ports. For each port, the
screen displays:

Status

The link status of the port.

TxPkts

The number of packets transmitted on this port since reset or manual clear.

RxPkts

The number of packets received on this port since reset or manual clear.

Collisions

The number of collisions on this port since reset or manual clear.

Tx B/s

The current transmission (outbound) bandwidth used on the WAN and LAN ports.

Rx B/s

The current reception (inbound) bandwidth used on the WAN and LAN ports.

Up Time

The time elapsed since this port acquired the link.

Poll Interval

The intervals at which the statistics are updated in this screen.

Summary of Contents for RangeMax DGN3500






























































































































Search results

Summary of Contents for RangeMax DGN3500

Reviews:

Related manuals for RangeMax DGN3500

Brands by name

Popular brands

NETGEAR RangeMax DGN3500, User Manual

Search results

Summary of Contents for RangeMax DGN3500

Reviews:

Related manuals for RangeMax DGN3500

Brands by name

Popular brands