NETGEAR RangeMax DGN3500 User Manual Download Page 103 | Manualshive

Page: 103 / 125

background image

Chapter 7: Troubleshooting

|

103

N300 Wireless Gigabit ADSL2+ Modem Router DGN3500 User Manual

If the power LED is still red 1 minute after power up:

•

Turn the power off and on to see if the router recovers.

•

Clear the router’s configuration to factory defaults. This sets the router’s IP address to

192.168.0.1. This procedure is explained in

Using the Wireless On/Off and WPS

Buttons to Reset the Router

on page 111.

If the error persists, you might have a hardware problem and should contact Technical
Support.

LAN or ADSL Port LED Is Not On

If either the LAN LEDs or ADSL Link LED does not light when the Ethernet connection is
made, check the following:

•

Make sure that the Ethernet cable connections are secure at the router and at the hub or

workstation.

•

Make sure that power is turned on to the connected hub or workstation.

•

Be sure you are using the correct cable: when connecting the ADSL port, use the cable

that was supplied with the wireless modem router. If the ADSL link LED is still off, this
may mean that there is no ADSL service or the cable connected to the ADSL port is bad.

Window Appears Asking You to Reload Firmware

If a window appears with a message asking you to reload the firmware, this indicates that a
problem has been detected with the current firmware. Please follow the on-screen
instructions to access new firmware and reload the firmware into your router.

«
...
101
102
103
104
105
...
»

Summary of Contents for RangeMax DGN3500






























































































































Reviews:

No comments

Related manuals for RangeMax DGN3500

Brand: Paradyne Pages: 2

Brand: Zhone Pages: 7

Brand: Zhone Pages: 1

Brand: IBM Pages: 32

JetWeb JX2-PR0FI1

Brand: Jetter Pages: 67

Brand: TP-Link Pages: 110

Brand: Eicon Networks Pages: 32

Brand: CalAmp Pages: 115

Brand: Patton Pages: 62

Brand: Hama Pages: 25

Brand: Infoblox Pages: 16

Brand: ZyXEL Communications Pages: 2

Brand: RadioSPECTRAL Pages: 2

Brand: Lanner Pages: 141

Brand: BinTec Pages: 2

Redbooks Emulex VFA5

Brand: IBM Pages: 15

Brand: LanReady Pages: 40

Brand: CTC Union Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands