NETGEAR RangeMax DGN3500 User Manual Download Page 119

Page: 119 / 125

Appendix C: Notification of Compliance

N300 Wireless Gigabit ADSL2+ Modem Router DGN3500 User Manual

FCC Caution

•

Any changes or modifications not expressly approved by the party responsible for compliance could void the

user’s authority to operate this equipment.

•

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

•

For product available in the USA market, only channel 1~11 can be operated. Selection of other channels is not

possible.

•

This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or

transmitter.

Canadian Department of Communications Radio Interference Regulations

This digital apparatus, (N300 Wireless Modem Router DGN3500), does not exceed the Class B limits for radio-noise

emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of

Communications.

Voluntary Control Council for Interference (VCCI) Statement

This equipment is in the Class B category (information equipment to be used in a residential area or an adjacent area

thereto) and conforms to the standards set by the Voluntary Control Council for Interference by Data Processing

Equipment and Electronic Office Machines aimed at preventing radio interference in such residential areas.
When used near a radio or TV receiver, it may become the cause of radio interference. Read instructions for correct

handling.

Interference Reduction Table

Household Appliance

Recommended Minimum Distance between



NETGEAR equipment and household appliance

to reduce interference (in feet and meters)

Microwave ovens

30 feet / 9 meters

Baby Monitor - Analog

20 feet / 6 meters

Baby Monitor - Digital

40 feet / 12 meters

Cordless phone - Analog

20 feet / 6 meters

Cordless phone - Digital

30 feet / 9 meters

Bluetooth devices

20 feet / 6 meters

ZigBee

20 feet / 6 meters

Summary of Contents for RangeMax DGN3500






























































































































Search results

Summary of Contents for RangeMax DGN3500

Reviews:

Related manuals for RangeMax DGN3500

Brands by name

Popular brands

NETGEAR RangeMax DGN3500, User Manual

Search results

Summary of Contents for RangeMax DGN3500

Reviews:

Related manuals for RangeMax DGN3500

Brands by name

Popular brands