NETGEAR Nighthawk RAX200 User Manual Download Page 14 | Manualshive

Page: 14 / 175

background image

Rear panel

The following figure shows the rear panel connectors and buttons.

Figure 3. Rear panel

Viewed from left to right, the rear panel contains the following components:

•

LED On/Off switch. Move the LED On/Off switch to the Off position to turn off the
router LEDs. The Power LED stays lit even if the LED On/Off switch is in the Off
position.

•

Reset button. Pressing the Reset button resets the router.
If the Reset button is pressed for at least 10 seconds and the Power LED blinks white,
the router returns to its factory settings. For information about the factory settings,
see Factory settings on page 173.

•

USB 3.0 ports 1 and 2. Use the two USB 3.0 ports to connect USB storage devices
to your router.

•

Internet port. One Gigabit Ethernet RJ-45 WAN port to connect your router to an
Internet modem such as a cable modem or DLS modem.

•

Ethernet ports. Use the four Gigabit Ethernet RJ-45 LAN ports to connect Ethernet
LAN devices to your router.

User Manual

14

Hardware Setup

Nighthawk Tri-Band AX12 12-Stream AX WiFi Router

«
...
12
13
14
15
16
...
»

Summary of Contents for Nighthawk RAX200
















































































































































































Reviews:

No comments

Related manuals for Nighthawk RAX200

Brand: GE Pages: 4

DG834GT - 108 Mbps Super G Wireless ADSL Router

Brand: NETGEAR Pages: 2

Marconi OMS 1200

Brand: Ericsson Pages: 136

Brand: Freund Pages: 6

Brand: ZyXEL Communications Pages: 12

Brand: CopperOptics Pages: 12

Brand: Edimax Pages: 15

Brand: Enterasys Pages: 62

BreezeNET DS.11 Configuration Utility

Brand: Alvarion Pages: 2

com.tom INDUSTRY 100.WLAN.W

Brand: Beck Pages: 2

Brand: Paradyne Pages: 28

DP1.2-Vision-IP-Fiber

Brand: G&D Pages: 240

Brand: Kasda Pages: 44

Matrix 6H303-48

Brand: Enterasys Pages: 90

GigaSpire BLAST u6

Brand: Calix Pages: 9

Cradlepoint AER1600

Brand: Choose 2 rent Pages: 5

Brand: Westermo Pages: 34

Brand: RadioLabs Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands