manualshive.com logo in svg

NETGEAR FSM7226RS - ProSafe Switch - Stackable, Hardware Installation Manual, Page: 30 / 34

Share
Download
NETGEAR FSM7226RS - ProSafe Switch - Stackable Hardware Installation Manual Download Page 30

Managed Layer 2+ Stackable Switches FSM7226RS and FSM7250RS Hardware Installation Guide

A-2

Default Factory Settings and Technical Specifications

v1.0, October 2008

Technical Specifications

This section provides technical specifications for the switches.

ACL 

Disabled 

GVRP 

Disabled 

GMRP 

Disabled 

IP routing 

Disabled 

MAC address aging 

300 seconds 

SNMP community 

public (read-only access), private (read/write access) 

DHCP Server 

Disabled

VLAN Ingress filtering

Enabled 

IP multicast filtering 

Disabled 

Table A-2.  Technical Specifications 

Feature

FSM7226RS

FSM7250RS

IEEE Network Protocol 
and Standards 
compatibility

802.3 10BASE-T
802.3u 100BASE-TX
802.3z 1000BASE-SX
802.3z 1000BASE-LX
802.3ab 1000BASE-T
802.3x flow control 

Table A-1.  Default Configuration Settings (continued)

Features

Default Setting

Summary of Contents for FSM7226RS - ProSafe Switch - Stackable



































Reviews:

No comments