NETGEAR FSM7226RS - ProSafe Switch - Stackable Hardware Installation Manual Download Page 3

v1.0, October 2008

iii

Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice 

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 

This device  not cause harmful interference. 

This device must accept any interference received, including interference that  cause undesired operation. 

Note:

 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a 
residential installation. This equipment generates, uses, and may radiate radio frequency energy and, if not installed and 
used in accordance with the instructions,  cause harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to 
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try 
to correct the interference by one or more of the following measures: 

Reorient or relocate the receiving antenna. 

Increase the separation between the equipment and receiver. 

Connect the equipment into an outlet on a circuit different from that which the receiver is connected. 

Consult the dealer or an experienced radio/TV technician for help. 

Canadian Department of Communications Radio Interference Regulations 

This digital apparatus (NETGEAR ProSafe™ 24-Port L2+ Managed Stackable Switch with 2 Gigabit ports 
FSM7226RS) does not exceed the Class A limits for radio-noise emissions from digital apparatus as set out in the Radio 
Interference Regulations of the Canadian Department of Communications. 

This digital apparatus (NETGEAR ProSafe™ 48-Port L2+ Managed Stackable Switch with 2 Gigabit ports 
FSM7250RS) does not exceed the Class A limits for radio-noise emissions from digital apparatus as set out in the Radio 
Interference Regulations of the Canadian Department of Communications. 

Règlement sur le brouillage radioélectrique du ministère des Communications 

Cet appareil numérique (NETGEAR ProSafe™ 24-Port L2+ Managed Stackable Switch with 2 Gigabit ports 
FSM7226RS) respecte les limites de bruits radioélectriques visant les appareils numériques de classe A prescrites dans 
le Règlement sur le brouillage radioélectrique du ministère des Communications du Canada. 

Cet appareil numérique (NETGEAR ProSafe™ 48-Port L2+ Managed Stackable Switch with 2 Gigabit ports 
FSM7250RS) respecte les limites de bruits radioélectriques visant les appareils numériques de classe A prescrites dans 
le Règlement sur le brouillage radioélectrique du ministère des Communications du Canada. 

EN 55 022 Declaration of Conformance 

This is to certify that the NETGEAR ProSafe™ 24-Port L2+ Managed Stackable Switch with 2 Gigabit ports 
FSM7226RS is shielded against the generation of radio interference in accordance with the application of Council 
Directive 89/336/EEC, Article 4a. Conformity is declared by the application of EN 55024 Class A (CISPR 22). 

This is to certify that the NETGEAR ProSafe™ 48-Port L2+ Managed Stackable Switch with 2 Gigabit ports 
FSM7250RS is shielded against the generation of radio interference in accordance with the application of Council 
Directive 89/336/EEC, Article 4a. Conformity is declared by the application of EN 55024 Class A (CISPR 22). 

EN 55 022 and EN 55 024 Statements 

This is to certify that the NETGEAR ProSafe™ 24-Port L2+ Managed Stackable Switch with 2 Gigabit ports 
FSM7226RS is shielded against the generation of radio interference in accordance with the application of Council 

Summary of Contents for FSM7226RS - ProSafe Switch - Stackable



































Reviews: