manualshive.com logo in svg

NETGEAR FSM7226RS - ProSafe Switch - Stackable, Hardware Installation Manual, Page: 29 / 34

Share
Download
NETGEAR FSM7226RS - ProSafe Switch - Stackable Hardware Installation Manual Download Page 29

Default Factory Settings and Technical Specifications

A-1

v1.0, October 2008

Appendix A 

Default Factory Settings and Technical 

Specifications

Default Configuration Settings

This section provides the default settings for the FSM7226RS and FSM7250RS switches.

Table A-1.  Default Configuration Settings 

Features

Default Setting

Port speed 

Auto-negotiation 

Port duplex 

Auto-negotiation 

Flow control (half duplex)  Enabled 

Flow control (full duplex)  Disabled 

Broadcast storm control 

Enabled 

Gigabit port type 

Auto detect 

Management IP 
configuration 

DHCP

Password protection 

Disabled 

User name 

Admin 

Password 

(none) 

Web access 

Enabled 

Java mode 

Enabled 

VLAN 

All ports belong to default VLAN (VLAN 1) as untagged ports 

IP multicast filtering 

Disabled 

Spanning Tree Protocol 

Enabled (IEEE 802.1s) 

Admin edge port 

Enabled 

Link aggregation 

Disabled 

Port mirroring 

Disabled 

Traffic prioritization 

Disabled

Summary of Contents for FSM7226RS - ProSafe Switch - Stackable



































Reviews:

No comments