NetApp DE460C Replacing Manual Download Page 2

Before you begin

You have obtained the following items:

Antistatic protection

Attention: 

Possible hardware damage – To prevent electrostatic discharge damage to the drive shelf, use proper

antistatic protection when handling drive shelf components.

Replacement drive drawer

Replacement left and right cable chains

Flashlight

Permanent marker

You have installed SANtricity System Manager on a management station, so you can use the storage array's command
line interface (CLI)

Note: 

If this software has not yet been installed, follow the instructions in the 

SANtricity System Manager Express

Guide or the SANtricity Power Guide for Advanced Users for your operating system to download and install it.

Steps

1. 

Preparing to remove a drive drawer

 on page 2

2. 

Removing the cable chains

 on page 5

3. 

Removing a drive drawer

 on page 10

4. 

Installing a drive drawer

 on page 13

5. 

Attaching the cable chains

 on page 14

6. 

Reinstalling the drives

 on page 18

Related information

SANtricity System Manager 11.40 Installing and Configuring for Linux Express Guide
SANtricity System Manager 11.40 Installing and Configuring for VMware Express Guide
SANtricity System Manager 11.40 Installing and Configuring for Windows Express Guide
SANtricity 11.40 Installing and Configuring for Linux Power Guide for Advanced Users
SANtricity 11.40 Installing and Configuring for VMware Power Guide for Advanced Users
SANtricity 11.40 Installing and Configuring for Windows Power Guide for Advanced Users

Preparing to remove a drive drawer

If the drive shelf is powered on, you must issue the 

Set Drawer Service Action Allowed Indicator

 CLI command to

prevent the controller from accessing the drive drawer. This command also allows you to determine if the drives in the drawer
are in volume groups or disk pools protected by Drawer Loss Protection. If the command fails, you will need to power off the
controller shelf before replacing the drawer.

Before you begin

Before issuing the CLI command, confirm that the drive shelf meets all of these conditions:

The drive shelf cannot be over temperature.

Both fans must be installed and have a status of Optimal.

All drive shelf components must be in place.

2

Summary of Contents for DE460C























Reviews: