Ness Auto IP NVR Setup Manual Download Page 63

Page: 63 / 94

OSD Setup Manual

Database Setup

The menu displays information of internal and external disks. In the Main menu, move the

cursor to <Database> and press ENTER. The following menu is displayed.

Database

Total Size
Free Size
Avail. Rec Time
Est. Rec Period
Internal Disks
External Disks
Data Protection
Repair On Power Loss

xxxGB

xxxGB (Circular)

(Circular)

3Days 10Hrs

NOTE: If detection of the hard disk fails, the “HDD fail” icon will be displayed.

< Total / Free Size of HDD >

The Total Size of HDD shows the total capacity of HDD that has been added to the

database. The Free Size of HDD indicates the free space for recording into the HDD that’s

added to the database. The information is “read only”.

< Avail. Rec Time >

The Avail. Rec Time indicates the available time duration for recording. If the unit is set to

record in circular mode, the item will show “Circular”. The information is “read only”.

< Est. Rec Period >

This item displays the estimated total recording duration, according to the current recording

settings. The information is “read-only”.

Summary of Contents for Auto IP NVR































































































Search results

Summary of Contents for Auto IP NVR

Reviews:

Brands by name

Popular brands

Ness Auto IP NVR, Setup Manual

Search results

Summary of Contents for Auto IP NVR

Reviews:

Brands by name

Popular brands