manualshive.com logo in svg

Ness Auto IP NVR, Setup Manual

Share
Download
Ness Auto IP NVR Setup Manual Download Page 36

  Manual 

35

 

< Audio Output/ Key Beep > 

Enter this item to setup the audio output or key beep.   

 

Audio Output/Key Beep 

Audio Output 
Audio Output Gain 
Key Beep 

Live/PB 

0 

On 

 

  Audio Output 

The item is used to set the audio output mode. The available options are as 

follows. 

 

Live/PB: 

Select the item to play the recording sounds of live image in live mode, and 

sounds of recorded video in playback mode respectively. 

 

Always Live: 

Select the item to play live sounds in both live mode and playback mode.   

 

OFF: 

Select the item to disable the audio output function. 

 

 

  Audio Output Gain 

The  item  is  used  to  adjust  volume  of  the  audio.  The  greater  the  value  -  the 

louder the sound. 

 

  Key Beep 

The item is used to enable or disable the key tone. Select 

<On>

 to enable the 

key tone, or 

<Off>

 to disable. 

 

 

Summary of Contents for Auto IP NVR































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands