background image

 

 

 

3

 

I N T RO D U C T I O N

ACCU-18XE LIQUID LAMINATOR 

Thank you for purchasing the Neschen-Accutech 
ACCU-18XE Liquid Laminator. The ACCU-18XE 
has been designed to provide you with years of reliable 
service. As you become more familiar with the 
laminator, you will appreciate the high quality of 
production it offers as well as the excellence in its 
engineering design. 

If the guidelines for proper care and use of the 18XE 
are followed, you will be able to depend on many years 
of trouble-free profitability from your investment. 

Please read and fully understand the entire 
manual before using your laminator. 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 1: ACCU-18XE Liquid Laminator

STATEMENT OF INTENDED USE 

The ACCU-18XE Liquid Laminator is ETL/UL 
approved and meets all relevant CE Safety Directives. 
It is intended for use with small format graphics 
output.  Graphics can vary in widths from 4”-18”    
(10.2 cm -45.7 cm) and in length from 6”-24” (15.2 
cm-61 cm).  The ACCU-18XE is designed for use 
with Neschen-Accutech lacquer only.  Use of other 
manufacturers’ lacquer may damage the machine and 
will void any warranty. 

 

WARNING:  This laminator is designed for 

laminating. Any use for purposes 
other than that for which the 
machine was designed may cause 
damage to the laminator or physical 
harm to the user. 

 

WARNING:  Any unauthorized changes or 

modifications to this unit without 
prior written approval from Neschen-
Accutech will void the user’s 
warranty and will transfer health and 
safety obligations to the user. 

 

LIABILITY STATEMENT 

Details provided in this manual are based on the most 
current information available. However, these details 
may be subject to change in the future. Neschen-
Accutech retains the right to make changes to the 
construction or design of their products without 
accepting any responsibility for modifying earlier 
versions previously delivered. 

 

CAUTION:  Pay attention to all passages marked 

in bold. This information is vital to 
preventing user injury and/or 
damage to the unit. Failure to follow 
this information could void the 
user’s warranties and transfer all 
safety obligations to the user.

Summary of Contents for ACCU-18XE

























Reviews: