![background image](http://html.mh-extra.com/html/hama/lg236/lg236_manual_583083001.webp)
6. Wait until the laminate has passed completely through the machine before removing it. Once it
has passed completely through, remove the laminate quickly to avoid over-heating of the end.
Notes on the Use of the Laminating Machine
1. If better laminating effect is desired, please allow further 10-20 minutes after the ready
indicator is on, in order to obtain better laminating quality.
2. Please do not only roll the laminating pouch film into the machine. it is forbidden to use
laminating pouch film single-sided. This is to prevent laminating pouch film to be rolled into the
laminator.
3. Please make sure that the total thickness to be laminated is not more tham 0.5 mm. Please do
not enter the laminating pouch obliquely in order to avoid the pouch film being stuck during
lamination.
4. Please disconnect the power plug when the unit is not in use for a long time.
5. Please send the unit to the appointed local distributor for repair, if there are any misuses of
laminating machine, resulting in the roll-in of laminating pouch film.
Cleaning & Maintenance of the Laminating Machine
Cleaning of the Roller
Should the laminating machine be used for a period, the rollers will be left with pouch film additives
that stuck on the laminating pouch film. This is one reason that the laminating puch will be rolled
into the roller. Therefore, please clean the roller periodically. Allow it to pass through the machine
about 10 times once the machine has been turned on and has been warm for roughly 30 minutes.
Cleaning of the Machine itself
1. Unplug the power supply cord before cleaning the unit!
2. Please wipe with soft cloth.
3. When necessary, wipe with neutral cleaning agent and rub it off with clean cloth.
50087
00050087-0
7.03
L
Laminator
50087
max.
max.
Laminiergeschwindigkeit
Laminier-
Laminierbreite
Laminierhöhe
50 Hz
60 Hz
temperatur
238 mm
125 mic
270mm/Min. 320mm/Min.
105°C
Notes on Safety:
Please read this manual carefully before use and follow the instructions below:
1. Do not use this unit outdoors.
2. Do not throw it on the ground heavily otherwise the outer shell will bi broken cousing dangers
of electric shock. Should there be any above-mentioned situation, please unplug in order to
avoid electric shock.
3. Please do not allow children to use this unit in order to avoid dangers.
4. Please do not dissassemble this unit by yourself as to avoid dangers of electric shock.
5.
Please do not place this unit where it is humid and wet. Please do not rub this unit with wet cloth.
6. Use the laminator only by watching it!
7. Do not covering the laminator (ventilation slits), because of overheating!
Methods of Use of the Laminating Machine
1. Please install the back directing pad on to the unit a sinstructed, and take notice of the exit of
the laminating machine to make sure there is no object obstructing its path/exit. Please also
preserve a space for the exit for the laminated item.
2. Insert the power plug into a socket with specification suitable for this unit.
3. Please turn on the switch on the upper right corner to”–” downwards. The power indicator is
on, and the laminating machine is now heating up.
4. The warm-up phase lasts about 10 minutes. The blinking green LED will stop blinking and
instead will light continuously, accompanied by an audio signal, to indicate the end of the
warm-up phase. For a higher laminating capacity (especially for larger quantities), let the
machine warm up for an additional 5 minutes.
NOTE: Total thickness to be laminated is 0.5 mm and max, width is 238 mm
5. Leave at least 3-5 mm space at the edges when inserting the item into the laminating pouch
film. Make sure there is no oblique insertion. Send the sealed side of the laminating pouch film
into the entrance of laminating machine.