English
8
English
9
automatically vary the preservation cycle set at
any time. Repeatedly press button (12) until the
LED that corresponds to the desired cycle is
activated. The LED will flash for 3 seconds and
becomes steadily lit: the new preservation cycle
is selected at this point and will be performed at
the end of the program. Each preparation
program will activate at the end of the selected
preservation cycle.
PADDLE LOCK UPON LID OPENING
The opening of the lid (3) only stops paddle (5)
and does not affect the preparation program.
The closure of the lid (3) starts the motion of the
paddle (5) (where, at that time it is provided by
the selected program). If the mixture proves
excessively thick to prevent the movement of
the paddle, the machine will automatically
activate the previously selected preservation
cycle.
AUTOMATIC PRESERVATION
There are 4 preservation cycles available for
every whipping program (total of 16 cycles)
devised to meet a wide range of needs.
•In automatic mode, if the machine is not
stopped, at the end of each production cycle
is enabled the ice cream preservation cycle
selected.
•The activation of the preservation function is
i n d i c a t e d b y f l a s h i n g o f t h e L E D
corresponding to the processing program of
the ice cream selected.
•The desired cycle selection can take place
either at the beginning or during the
processing phase.
•Depending on the type of recipe and/or the
quantity prepared, every set of preservation
cycles enables keeping gelato, Granita and
sorbet or other whipped products at the
desired conditions.
•Pressing the button (12) several times causes
the selection LEDs of the various preservation
cycles to light up in sequence. If you switch
from the first (LED (12a) active) to the fourth
(LED (12d) active) preservation program, the
density of gelato increases gradually.
•Once you have selected the desired cycle, the
corresponding LED will flash for 3 seconds
and will become steadily lit, enabling the
selection.
VARIATION OF THE PRESERVATION CYCLE
You can always select a different preservation
cycle either during the active phase and during
the pause phase of the running cycle.
Repeatedly press button (12) until the LED that
corresponds to the desired cycle is activated.
The LED will flash for 3 seconds and become
steadily lit: The new preservation cycle is now
selected and it will be run for the set execution
times
Should it become necessary to switch to a
preservation cycle associated to a different
program, you must enable the corresponding
program priorly, by pressing the button (11).
Once you have enabled the program, switch to
the preservation cycle by pressing buttons (2)
and (1) simultaneously for 3 seconds. The
machine will enable the preservation cycles
associated to the preset program.
SWITCHING FROM PRESERVATION PHASE
TO A PRODUCTION PROGRAM
With the preservation active, you can activate
an automatic program simply by selecting it by
pressing button (11). The LED corresponding to
the selected program will flash for 3 seconds
and become steadily lit; the machine will exit the
preservation cycle and run the selected
program.
Subsequently, the preservation cycles
associated to the selected program ill be
enabled.
PADDLE LOCK UPON LID OPENING
The opening of the lid (3) only stops the paddle
(5) and does not affect the preservation cycle.
The closure of the lid (3) enables the paddle
operation (5) (on the condition that it is provided
by the selected preservation cycle in that
moment). If the mixture proves excessively hard
and prevents the movement of the paddle, the
machine will automatically re-activate the
preservation cycle from the start.
TURNING OFF THE MACHINE DURING
PRESERVATION
To turn off the machine, hold down button (11)
for 3 seconds and then act on the main switch
(10). Do not act directly on the main switch (10)!
IMPORTANT
•Each preservation cycle continues until the
user decides to stop it.
•The machine is not designed for use either for
storage or as a refrigerator! Store the
preparation in the pot for no longer than 12
hours.
the button (11), you will be able to select other
programs in sequence.
•When the LED becomes steadily lit, the
associated program starts up and begins the
production cycle.
•The machine has 4 production programs and
4 preservation cycles for each of them. When
the program selected starts up you can
choose the preservation cycle desired. Chose
the preservation cycle by pressing the button
(12) repeatedly. When switching from the first
preservation program to the fourth, gelato
consistency increases gradually.
•When the ice cream reaches the right
consistency, the production program stops
automatically and the preset preservation
cycle is enabled.
•Every production program has a preset
threshold time after which the machine enters
in preservation cycle, regardless of the current
production phase.
•If deemed appropriate, it is possible to enable
the selected preservation cycle at any time ,
ending the production program. Select the
preservation cycle desired via the key 12
(sequence selection). Keep the paddle button
(2) an compressor button (1) pressed
simultaneously for 3 seconds. The machine
will immediately switch from production cycle
to preservation cycle.
•CLASSIC ITALIAN GELATO AND SORBET
PROGRAM. By pressing button (11) once, the
LED (11a) will light up and activate the
production program. At the end of the
production cycle, the LED (11a) flashes
indicating that the selected preservation cycle
has been activated.
If the preparation was ready before reaching
the operation time limit, the whipping paddle
l o c k s . T h e p r e s e r v a t i o n f u n c t i o n i s
automatically activated.
•
. By pressing
SEMI-SOFT GELATO PROGRAM
button (11) twice, LED (11b) will light up and
activate the processing program. At the end of
the production cycle, the LED (11b) flashes
indicating that the selected preservation cycle
has been activated.
If the preparation was ready before reaching
the operation time limit, the whipping paddle
l o c k s . T h e p r e s e r v a t i o n f u n c t i o n i s
automatically activated.
•
. By pressing button (11)
GRANITA PROGRAM
three times causes LED (11c) to light up and
activate Granita processing. At the end of the
production cycle, the LED (11c) flashes
indicating that the selected preservation cycle
has been activated.
If the preparation was ready before reaching
the operation time limit, the whipping paddle
l o c k s . T h e p r e s e r v a t i o n f u n c t i o n i s
automatically activated.
•
Pressing button
FAST COOLING PROGRAM.
(11) four times causes LED (11d) to light up
and activate the fast cooling program. At the
end of the production cycle, the LED (11d)
f l a s h e s i n d i c a t i n g t h a t t h e s e l e c t e d
preservation cycle has been activated.
This program is used when processing
mixtures with high initial temperatures. The
program quickly brings down the temperature
without adding too much air into the mixture,
saving time and improving the quality of the
ice cream made.
SELECTED PROGRAM VARIATION
Should it become necessary to select a
different program when a program is running,
you can simply press button (11). When the new
program is selected, the currently running
program will stop. The new program will be
active immediately with its own execution times
that will restart from the initial values.
SWITCHING FROM AUTOMATIC TO MANUAL
OPERATION
During the processing program, it is possible to
switch to manual mode at any time.
Holding down button (11) for 3 seconds
switches the machine to manual mode while
enabling the paddle LEDs (2a) and compressor
(1a).
The preservation cycle selected will be
deactivated.
TURNING OFF THE MACHINE DURING
AUTOMATIC OPERATION MODE
If you need to turn off the machine before the
completion of the active processing program,
you first need to switch to manual mode by
pressing and holding button (11) for 3 seconds
and then pressing paddle (2) and compressor
(1) to stop any activity. Do not act directly on the
main switch (10)!
PRESERVATION CYCLE VARIATION WHILE A
PROGRAM IS RUNNING
During the preparation phase it is possible to
