background image

9

The controller has 4 separate, user-selectable sets of settings for configuring the RO. The factory default 

settings are shown below. The settings are identical except for variations in the flush behavior.
 • 

Program 1

High Pressure flush

 • 

Program 2

No Flush

 • 

Program 3

Permeate Flush, (low pressure, inlet valve closed)

 • 

Program 4

Low Pressure, feed water flush

See the previous page for instructions on how to access the menu for selecting these programs.
See Appendix A for a detailed explanation of the Parameters and their affect on the RO’s operation.

  Table 2 - Controller Programming:  

ROC2HE Program Selections

Parameter

Value

Program 1

Program 2

Program 3

Program 4

Tank Level Switch delay

 (actuation and de-actuation)

Seconds

2

2

2

2

Pressure Switch delay (actuation and de-actuation)

Seconds

2

2

2

2

Pretreat Switch delay (actuation and de-actuation) 

Seconds

2

2

2

2

Pump start delay

Seconds

10

10

10

10

Inlet Solenid stop delay

Seconds

1

1

1

1

Pump start retry interval (restart delay after LP fault)

Seconds

60

60

60

60

Low pressure fault shutdown, # of faults

Faults

5

5

5

5

Low pressure fault shutdown, time period to count faults

Minutes

10

10

10

10

Low pressure fault shutdown, reset after shutdown

Minutes

60

60

60

60

Low pressure time out fault

Seconds

60

60

60

60

Flush Behavior

High Pressure

No Flush

Perm Flush

Low Pres Flush

Startup Flush:

 Minutes from last flush

Minutes

0

0

0

0

Startup Flush:

 Duration 

Seconds

0

0

0

30

Periodic Flush:

 Interval

Minutes

60

0

0

Periodic Flush: 

Duration

Seconds

30

0

0

0

Shutdown Flush:

 Time from last flush

Minutes

10

0

0

0

Shutdown Flush:

 Minumum operation

Minutes

30

0

0

0

Shutdown Flush:

 Duration

Seconds

60

0

60

60

Idle Flush:

 Interval *

Minutes

0

0

0

0

Idle Flush:

 Duration *

Seconds

0

0

0

0

Timed Manual Run

Minutes

5

5

5

5

Timed Manual Flush

Seconds

5

0

5

5

*  These features are disabled by default due to the potential for confusion on the part of end-users in the field. 

They can be enabled when needed via the OEM PC programming interface which allows changes to all of 

the values shown above.

Summary of Contents for NRO ROC2HE-UL

















Reviews: