background image

Page 9 of 13

Neets Control - 

Sierra II, DK

P/N#: 310-0202

LAN

GND
+12V

 
RX-1
TX-1
GND

 
TX-2
TX-3
GND

I/O 3
I/O 2
I/O 1
GND

 
GND
NCL
NDA
PWR
 

RoHS

Neets Control - 

Sierra II, DK

P/N#: 310-0202

LAN

GND
+12V

 
RX-1
TX-1
GND

 
TX-2
TX-3
GND

I/O 3
I/O 2
I/O 1
GND

 
GND
NCL
NDA
PWR
 

RoHS

PIN 2 <-> Tx
PIN 3 <-> Rx
PIN 5 <-> GND

Connections and Controls

Power input port

Connect the SieRRa II to the supplied AC  

power adaptor using the supplied 2 pole screw 

block terminal. White/black wire connects to 12V, 

black wire connects to GND. 

The SieRRa II adaptor incorporates a universal 

mains input which accepts AC line input from 100 V 

to 240 V.

Note: If using the PoE functionality to power the 

SieRRa II, do not connect the AC power adaptor. 

 

I/O ports

The three I/O (Inputs/Outputs) can be configured as 

either output or input. Each is available for  

connection to a PIR (movement) sensor, keyboard 

lock, relays or for other compatible uses. The ports 

are not potential free; you may need external relays 

to prevent ground loops depending on your  

application. 

When used as outputs, the I/O ports are active 

low. When activated, the I/O ports are tied to GND 

through a FET transistor (also called open drain/ 

collector function). Each I/O can draw up to  

24VDC/500mA. 

When used as inputs, the applied voltage must be 

below 1 VDC to be accepted as LOW, and above 4 

VDC (but below 24 VDC) to be accepted as HIGH. 

The inputs are default HIGH and must be connected 

to ground in order to change state.

RS-232/IR ports

The RS-232 ports (TX-1, RX-1, TX-2, TX-3) are used 

for one- or two-way communication. Port 1 is a two 

way port, which can be used for devices for which a 

reply function is required, such as a projector.

LAN

GND
+12V

 
RX-1
TX-1
GND

 
TX-2

I/O 3
I/O 2
I/O 1
GND

 
GND
NCL

RoHS

LAN

GND
+12V

 
RX-1
TX-1
GND

 
TX-2

I/O 3
I/O 2
I/O 1
GND

 
GND
NCL

RoHS

Relay control

Input trigger

Relay

Switch

Summary of Contents for SieRRa II 310-0102














Reviews: