background image

L-PAK 150/250 Advanced

EN

6

Preface

Read this manual carefully before installation, use and service of this product. 

Replace the manual immediately if lost. Nederman reserves the right, without 

previous notice, to modify and improve its products including documentation.
This product is designed to meet the requirements of relevant EC directives. To 

maintain this status, all installation, maintenance and repair is to be done by 

qualified personnel using only Nederman original spare parts and accessories. 

Contact the nearest authorized distributor or Nederman for advice on 

technical service and obtaining spare parts. If there are any damaged or 

missing parts when the product is delivered, notify the carrier and the local 

Nederman representative immediately.

Safety

This document contains important information that is presented as either a 

warning, caution or note. See the following examples:

WARNING! 

Risk of personal injury.

Warnings indicate a potential hazard to the health and safety of personnel, 

and how that hazard may be avoided. 

CAUTION! 

Risk of equipment damage. 

Cautions indicate a potential hazard to the product but not to personnel, and 

how that hazard may be avoided.

NOTE! 

Notes contain other information that is important for personnel.

Description

WARNING! 

Risk of personal injury.

See the User manual

Unit operation

4.1 

Software with extended functionality

L-PAK 150/250 Advanced comes with special software that works with or 

without the Logo! display that is included.

NOTE! 

If the software is used in a logo without a display, it is not possible to 

change parameter settings.

Summary of Contents for L-PAK Series



















Reviews: