background image

L-PAK 150/250 Advanced

EN

14

15. 

Press 

OK 

 to confirm.

16. 

Press 

ESC 

 to go to the main menu.

17. 

Press 

ESC 

 to go to the date and time screen.

18. 

Press 

 to exit.

Setting WeekTim 2, Monday–Friday afternoons

WeekTim 2

D=MTWTF--

On=13:00

Off=16:00

ESC

OK

Make the settings according to the previous section.

Setting WeekTim 3, Saturday–Sunday afternoons

WeekTim 3

D=-----SS

On=--:--

Off=--:--

ESC

OK

Make the settings according to the previous section.

Setting WeekTim 4

WeekTim 4 is to be set to off at all times.

6.2.3 

H-Meter 1

Menu for setting the service interval. The default value is 2000 hours.

H-Meter 1

MI = 2000h

ESC

OK

MI =2000h: The amount of time between service 

intervals.

6.2.4 

DIR_Time

Menu for setting the DIR timer. The DIR timer is the amount of time before 

the unit goes from Running mode into Idling mode when the pilot signal 

disappears.

DIR_Time

T = 10:00s

Ta = 00:00

ESC

OK

T=10:00s: Time before DIR_Time is activated. 

The default setting is 10 seconds The minimum 

setting is 5 seconds.

Ta=00:00: The elapsed time since the pilot signal 

disappeared.

6.2.5 

SSR_Time

Menu for setting the SSR timer. The SSR timer is for the amount of time 

before the unit goes from Idling mode to Standby mode when the pilot signal 

disappears.

Summary of Contents for L-PAK Series



















Reviews: