NEC SL1100 Programming Manual Download Page 581 | Manualshive

Page: 581 / 666

background image

Alarm

No.

Type

Re-

port

Name

Content of

Alarm

Cause

Action

Recovery

Alarm

Status

3

2

0

Connec-
tion fault
between
CPU and
other
PKGs.

The error occur-
red when com-
municating with
the package.
When the pack-
age is broken, it
recognizes it as
a communica-
tion fault.

1.

The unit is not
completely in-
serted.

2.

The power-
supply voltage
of the system
is outside rat-
ings.

3.

The equip-
ment that gen-
erates the
noise in the
same power
supply system
as the power
supply origin
of the system
is connected,
and it malfunc-
tions because
of the power
supply noise.

4.

The equip-
ment to which
it is adjacent
to of a main
device, and
has put out
the radiation
noise exists,
and it malfunc-
tions because
of the radia-
tion noise.

5.

The chassis is
not properly
grounded.

1.

Please insert
the unit firmly.

2.

The power-
supply voltage
must use an-
other power
supply when is
in the range of
ratings or
measuring
with the volt-
meter, and de-
viating from
the rated
range.

3.

Please use the
power supply
besides the
equipment
with the possi-
bility of the
noise source.

4.

Please sepa-
rate as much
as possible
and use a
main device
from the
equipment by
which you
seem may
generate the
radiation
noise.

5.

Please ground
the chassis
correctly.

When unit is
confirmed,
the error is
recovered.

ERR
REC

4

2

0

PKG S/W
Download
Error

The unit pro-
gram could not
be downloaded
normally.
The unit could
not able to be
started normal-
ly.

1.

The package
software is not
stored in the
downloaded
USB memory.

2.

The stored
package soft-
ware is illegal.
Package infor-
mation that
was installed
before re-
mains.

1.

Delete slot in-
formation that
corresponds
by Program
90-05-01 to
delete pack-
age informa-
tion that was
installed be-
fore.

2.

There is a
possibility that
the unit pro-
gram is broken
though an ex-
ternal factor of
the noise etc.
is thought.

3.

Please load in-
to the USB
memory and
try again when
you back up
the unit pro-
gram.

4.

Please Check
with maker on
uncertain
points.

Please ex-
change units,
though it is
likely to re-
store by
mounting the
unit again.
When the unit
program is
normally
downloaded,
the error is
recovered.

ERR
REC

ISSUE 3.01

SL1000/SL1100

Programming Manual

2-559

Program

90

«
...
579
580
581
582
583
...
»

Summary of Contents for SL1100



























































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SL1100

Brand: Fancom Pages: 31

Brand: 3M Pages: 90

Brand: JBL Pages: 24

Brand: Jensen Pages: 4

Brand: Jensen Pages: 48

Brand: J&M Pages: 8

Audio Center Floor Stand I Compose

Brand: Loewe Pages: 52

Brand: ALLEN & HEATH Pages: 14

Brand: JiangYi Pages: 13

Brand: Revo Pages: 6

Brand: vistaCNC Pages: 7

Brand: LOGICDATA Pages: 32

Brand: Polaris Pages: 8

Brand: Panasonic Pages: 8

SAPM71 - MINI HES W/CD PLAYER

Brand: Panasonic Pages: 12

SAPM31 - MINI HES W/CD PLAYER

Brand: Panasonic Pages: 16

Brand: Panasonic Pages: 20

SAPM41 - MINI HES W/CD PLAYER

Brand: Panasonic Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands