NEC SL1100 Programming Manual Download Page 56 | Manualshive

Page: 56 / 666

background image

Program 10 : System Configuration Setup

10-28 : SIP System Information Setup

Level:

SA

Description

Use

Program 10-28 : SIP System Information Setup

to set up basic SIP trunking.

Input Data

Item

No.

Item

Input Data

Description

Default

01

Domain Name

Up to 64 Characters
(ex. : UserID@Host-
Name.DomainName)

Set the domain name of the SIP-URL.

No Setting

02

Host Name

Up to 48 Characters
(ex. : UserID@Host-
Name.DomainName)

Set the host name of the SIP-URL.

No Setting

03

Transport Protocol

0 = UDP
1 = TCP

Set the protocol for the connection.

0

04

UserID

Up to 32 Characters
When assigning the
User ID, the ID may con-
tain only alpha charac-
ters. (A space and/or
special characters are
not allowed in the User
ID field).
(ex. : UserID@Host-
Name.DomainName)

User ID in the SIP Invite Setup message.
Use it for outbound caller ID information if
no information is assigned in commands
21-17, 21-19, 15-16, 14-12 and 10-36. A
call cannot be completed across the span
if there is no outbound CID info. The rea-
son for this is: the from and display portion
of the invite message would be blank, and
it would not know where the call originated
from.

No Setting

05

Domain Assignment

0 = IP Address
1 = Domain Name

If the information from Telco was a domain
name ([email protected]) then set to do-
main. If the information for Telco was a IP
address then set to IP Address.

0

06

IP Trunk Port Binding

0 = Disable
1 = Enable

Trunk port binding is only used for SIP
trunks to the provider in Non-Registration
Mode only. When this is disabled, an in-
bound call comes in and follows your DID
routing but it comes in on the first available
trunk. When enabled, the inbound call
comes in and follows your normal DID
routing but maps to that specified trunk. If
that trunk is busy, it sends back a busy un-
less you build a hunt group. To build the
hunt group, it references command
14-12-02 (pilot register ID). This then
points you to command 10-36-02. All the
numbers with the same pilot are in the
same hunt group.

0

Conditions

None

SL1000/SL1100

ISSUE 3.01

2-34

Program 10 : System Configuration Setup

Program

10

«
...
54
55
56
57
58
...
»

Summary of Contents for SL1100



























































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SL1100

Brand: VCON Pages: 66

Brand: RADVision Pages: 39

Brand: QNAP Pages: 35

Brand: Waterway Pages: 8

Brand: Panasonic Pages: 4

MME100 - Audio Micro System

Brand: Magnavox Pages: 23

Brand: V-ZUG Pages: 24

Brand: Uniden Pages: 141

Brand: Coby Pages: 3

EduTrainer 8071407

Brand: Festo Pages: 80

Brand: Rath Pages: 10

WALLACE & TIERNAN SFC SC

Brand: Evoqua Pages: 82

Brand: Grundig Pages: 34

Brand: RAM Pages: 36

Brand: SKF Pages: 63

Brand: Panasonic Pages: 24

Brand: Panasonic Pages: 24

Brand: Panasonic Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands