manualshive.com logo in svg

NEC POWERMATE PRO2180, Manual

The NEC POWERMATE PRO2180 user manual is available for free download on our website. This comprehensive manual will assist you in understanding and maximizing the potential of your product. Visit manualshive.com to easily access the manual and unlock the full capabilities of your POWERMATE PRO2180.

Share
Download
background image

    

 5-14   Installing Options

 

NOTE

 You may install AVL approved, 60-ns,

parity, fast page mode (FPM) SIMMs into the
SIMM sockets.

„

1-MB by 32- or 36-bit (4-MB stick)

„

2-MB by 32- or 36-bit (8-MB stick)

„

4-MB by 32- or 36-bit (16-MB stick)

„

8-MB by 32- or 36-bit (32-MB stick)

„

16-MB by 32- or 36-bit (64-MB stick).

 

 

!

CAUTION

 To avoid corrosion between different metals, only
use tin-plated SIMM sticks.

Checking System Memory

 Use the following procedure to:

„

check the memory installed in the system

„

determine the SIMM configuration needed to increase
memory

 

NOTE

 SIMM memory must be installed in pairs of

the same memory type.

Summary of Contents for POWERMATE PRO2180




















































































































































































































Reviews:

No comments

Related manuals for POWERMATE PRO2180

Gateway E-1200 User Manual preview
E-1200
Brand: Gateway Pages: 42
Production Basics RTW 3000 Assembly Manual preview
RTW 3000
Brand: Production Basics Pages: 3
Advantech IPC-690 User Manual preview
IPC-690
Brand: Advantech Pages: 19
Casio FX-890P Owner'S Manual preview
FX-890P
Brand: Casio Pages: 126
Acer Aspire M3910 Service Manual preview
Aspire M3910
Brand: Acer Pages: 74
Acer Aspire M3900 Service Manual preview
Aspire M3900
Brand: Acer Pages: 83
Acer Aspire M5810 User Manual preview
Aspire M5810
Brand: Acer Pages: 77
Acer Aspire M5810 Service Manual preview
Aspire M5810
Brand: Acer Pages: 97
Acer Aspire M3710 Service Manual preview
Aspire M3710
Brand: Acer Pages: 73
Acer Aspire T630 User Manual preview
Aspire T630
Brand: Acer Pages: 28
Acer Aspire M5802 Service Manual preview
Aspire M5802
Brand: Acer Pages: 105
Acer Aspire M3920 Service Manual preview
Aspire M3920
Brand: Acer Pages: 98
Acer Aspire T671 (Spanish) Guía Del Usuario preview
Aspire T671
Brand: Acer Pages: 30
Acer Aspire TC-865 User Manual preview
Aspire TC-865
Brand: Acer Pages: 52
Acer Aspire M5811 Service Manual preview
Aspire M5811
Brand: Acer Pages: 101
Acer Aspire M5400 Service Manual preview
Aspire M5400
Brand: Acer Pages: 95
Acer Aspire Timeline 4810T Service Manual preview
Aspire Timeline 4810T
Brand: Acer Pages: 148
Acer Aspire M3970 Service Manual preview
Aspire M3970
Brand: Acer Pages: 127

Brands by name

Popular brands

Load more brands