NEC POWERMATE PRO2180 Manual Download Page 159

Page: 159 / 211

6-10 Setting System Board Jumpers

CMOS Access

Access Denied

26-28

Access Allowed

28-30

(default)

Jumpers

Clear CMOS Jumper

Replace the system unit cover (see “Replacing the
System Unit Cover” in Chapter 5).

Connect system power cables and monitor.

Power on the system. The system displays a system
configuration error message.

Power off, unplug the system and monitor, and remove
the cover.

10.

Remove the jumper block from pins 26-28 and replace
it on pins 28-30.

11.

If you removed any expansion boards, replace them
(see “Replacing Expansion Boards” in Chapter 5).

12.

Replace the system unit cover. Reconnect the system
power cables and peripheral devices.

13.

Power on the system.

14.

Run Setup (see Chapter 4, NEC Drivers and Utilities).

Summary of Contents for POWERMATE PRO2180




















































































































































































































Search results

Summary of Contents for POWERMATE PRO2180

Reviews:

Related manuals for POWERMATE PRO2180

Brands by name

Popular brands

NEC POWERMATE PRO2180, Manual

Search results

Summary of Contents for POWERMATE PRO2180

Reviews:

Related manuals for POWERMATE PRO2180

Brands by name

Popular brands