manualshive.com logo in svg

NEC POWERMATE PRO2180, Manual

The NEC POWERMATE PRO2180 user manual is available for free download on our website. This comprehensive manual will assist you in understanding and maximizing the potential of your product. Visit manualshive.com to easily access the manual and unlock the full capabilities of your POWERMATE PRO2180.

Share
Download
background image

    

 Installing Options   5-45

 Connecting an RS-232C cable

Connecting a SCSI Device

 

NOTE

 Before connecting a SCSI device to the

system, be sure the SCSI device is set up correctly,
including the SCSI ID. Follow the setup instructions
that come with the option.

 Connect an external SCSI device to the back of the system
unit as follows.

1. 

Turn off power to the system unit and the SCSI device.

2. 

Connect one end of the SCSI cable to the SCSI port on
the rear of the system unit.

3. 

Secure the cable with the screws provided.

4. 

Connect the other end to the SCSI device.

 

Summary of Contents for POWERMATE PRO2180




















































































































































































































Reviews:

No comments

Related manuals for POWERMATE PRO2180

IBM PC 300GL Type 6267 Technical Information Manual preview
PC 300GL Type 6267
Brand: IBM Pages: 58
Compal U-BPC User Manual preview
U-BPC
Brand: Compal Pages: 57
Gateway GT5042j Getting To Know preview
GT5042j
Brand: Gateway Pages: 2
NEC POWERMATE - VERSION 2008 Manual preview
POWERMATE - VERSION 2008
Brand: NEC Pages: 32
DEC DECstation 316+ Service Manual preview
DECstation 316+
Brand: DEC Pages: 94
Biostar IDEQ 200V User Manual preview
IDEQ 200V
Brand: Biostar Pages: 58
EMAC PCM-6892E Quick Installation Manual preview
PCM-6892E
Brand: EMAC Pages: 28
I-Tech Digital Signage LCD integrated w/ PC... Specifications preview
Digital Signage LCD integrated w/ PC...
Brand: I-Tech Pages: 1
Vivo DESK-V000U Instruction Manual preview
DESK-V000U
Brand: Vivo Pages: 3
Asus BT14675 User Manual preview
BT14675
Brand: Asus Pages: 16
Dell Precision 370 - SX280 Ultra Small Form Factor Quick Reference Manual preview
Precision 370 - SX280 Ultra Small Form Factor
Brand: Dell Pages: 162
Toshiba Qosmio G50 Series Maintenance Manual preview
Qosmio G50 Series
Brand: Toshiba Pages: 446
Gigabyte HA-91 User Manual preview
HA-91
Brand: Gigabyte Pages: 26
blackbox-av BBPC-i7 Manual preview
BBPC-i7
Brand: blackbox-av Pages: 8
SWEDX SAB-200 User Manual preview
SAB-200
Brand: SWEDX Pages: 4
Aaeon BOXER-8320AI User Manual preview
BOXER-8320AI
Brand: Aaeon Pages: 73
Panasonic CF-51 Series Operating Instructions Manual preview
CF-51 Series
Brand: Panasonic Pages: 32
UMAX Technologies U-One 24GR Plus User Manual preview
U-One 24GR Plus
Brand: UMAX Technologies Pages: 52

Brands by name

Popular brands

Load more brands