NEC MultiSync FP1370 Service Manual Download Page 82

Page: 82 / 286

6-2

1-3. Operation

- The operation should be performed according to the screen message.

- When the message of “Please set Vsync to 42Hz.” is displayed, set the signal generator to the signal

with vertical synchronization frequency of 42Hz. When the message of “Please set Vsync to over 55Hz.”

is displayed, set the signal generator to the signal whose vertical synchronization frequency is between

55Hz and 25kHz.

The message of “Normally Complete” means that writing of EDID data or PnP inspection completed normally.

The message of “Error” means that writing of EDID data or PnP inspection finished incorrectly.

- When the PnP inspection is completed, read EDID data would be displayed. And if the read EDID data

differed from the original EDID data, the different bytes would be displayed in red.

- For the details of error, see the messages displayed at the bottom right of the screen. The meaning of

the messages is shown on section 4.

- After writing of EDID data or inspection of DDC2B, monitor can not be communicated by DDC1. In that

case, turn off and on the monitor again, which will make the DDC1 communication test possible.

- Make sure that fixture’s LED flashes on and off before writing EDID data, inspecting DDC1 and DDC2B.

If the fixture’s LED does not flash on and off, turn off and turn on the monitor and the fixture.

1-4. Error Messages

- Start Bit Error

This message is displayed when the start bit is not “H” while sending data from PC to MPU on the

fixture. This error will be caused by noise etc. on the line.

- Command Error

This message is displayed when the different command is sent from PC to MPU on the fixture.

- Hardware Error

This message means that the PC does not recognize ACK command sent from the MPU on the fixture.

- File Open Error

This message means that the input EDID file name was wrong.

- Command line Switch Error

This message means that the input communication command is incorrect.

- Parity Error

This message is displayed when the MPU on the fixture recognized the parity bit is incorrect. This error

can be caused by noise etc. on the line.

- EDID Data Error

This message is displayed when the null bit is not detected in EDID data read by DDC1 communication.

- EDID Data Sort Error

This message is displayed when the header code is not detected in EDID data read by DDC1 communication.

- Time Out Error

This message is displayed when the PC does not recognize ACK commands sent from MPU within

10m sec after the PC had sent communication command or EDID data. If this error occurs, check the

connection on PC, fixture and monitor.

Summary of Contents for MultiSync FP1370































































































































































































































































































Search results

Summary of Contents for MultiSync FP1370

Reviews:

Related manuals for MultiSync FP1370

Brands by name

Popular brands

NEC MultiSync FP1370, Service Manual

Search results

Summary of Contents for MultiSync FP1370

Reviews:

Related manuals for MultiSync FP1370

Brands by name

Popular brands