English-19
English
Tag4*
1
(Analog
input only)
AUTO ADJUST*
2
Automatically adjusts the Image Position and H.Size settings and Fine settings.
Press “SELECT” to activate Auto Adjustment. Please use test pattern, which is included
in the enclosed CD-ROM.
SIGNAL ADJUST
Determines when the auto adjustment is activated automatically.
The choices are “SIMPLE” and “FULL”. Press “Left” or “Right” to select.
H-size, Fine, H/V Position
Contrast
SIMPLE
O
X
FULL
O
O
O: Automatic Adjustment X: No Automatic Adjustment
NOTE: Automatic Adjustment does not work at resolutions less than 800x600 resolution.
AUTO ADJUST
LEVEL
Determines the automatic adjustment level for Auto Adjust. The choices are “SIMPLE”,
“FULL” and “DETAIL”. Press “Left” or “Right” to select. Refer to the below table.
Size, Fine, Position
Contrast
Black Level
Time
SIMPLE
O
X
X
1 second
FULL
O
O
X
1.5 seconds
DETAIL*
O
O
O
5 seconds
O: Automatic Adjustment X: No Automatic Adjustment
* “DETAIL” activates automatic long cable (skew, peaking) adjustment.
A-NTAA SW
The Advanced No Touch Auto Adjust function is able to recognize new signals even
when neither the resolution nor the refresh rate has changed. If several PCs are
connected to the monitor, and each transmit very similar (or even the same) signals in
terms of resolution and refresh rates, the monitor recognizes that there is a new signal
and automatically optimizes the picture without the need for any action on the part of the
user.
OFF: A-NTAA is disabled.
ON: If a change in signal is detected A-NTAA will adjust the monitor to the optimal
settings for the new signal. If no change in the signal is detected then A-NTAA does not
activate. The screen will be blank while the monitor optimizes the signal.
OPTION: Functions the same as ON, except that the screen does not go blank when the
monitor makes adjustments for changes in signal, allowing the monitor to display the new
signal faster. When using an external switching device to connect 2 or more PCs to the
monitor, using the ON or OPTION settings is suitable.
AUTO CONTRAST*
2
Adjusts the image displayed for non-standard video inputs. Press “SELECT” to adjust.
Any adjustment requires the image to have white portions.
CONTRAST
Adjusts the image brightness and contrast in relation to the background.
Press “Left” or “Right” to adjust.
AUTO BLACK LEVEL*
2
Automatically adjusts the black level. Any adjustment requires the image to have black
portions. Press “SELECT” to activate Auto Adjust.
BLACK LEVEL
Adjusts the RGB black level by input signal level.
Tag5
H.POSITION
Controls Horizontal Image Position within the display area of the LCD.
Press “Left” or “Right” to adjust.
V.POSITION
Controls Vertical Image Position within the display area of the LCD.
Press “Left” or “Right” to adjust.
H.SIZE*
1
(Analog input only)
Adjusts the horizontal size of the screen.
If the “AUTO Adjust function” do not give you a satisfactory picture setting, a further
tuning can be performed using the “H.Size (V.Size)” function (dot clock). For this a Moiré
test pattern could be used. This function may alter the width of the picture. Use left/Right
Menu to center the image on the screen. If the H.Size (V.Size) is incorrectly calibrated,
vertical bands will appear. The image should be homogeneous.
FINE*
1
(Analog input only)
Improve focus, clarity and image stability by increasing or decreasing this setting.
If the “Auto Adjust function” and the “H.Size” function do not give you a satisfactory
picture setting, a fi ne tuning can be performed using the “Fine” function. For this a Moiré
test pattern could be used. If the Fine value is incorrectly calibrated, horizontal lines will
appear on the display. The image should be homogeneous.
AUTO FINE*
1
(Analog input only)
This function automatically and periodically adjusts the “FINE” setting for change in signal
condition. This function adjusts approximately every 33 minutes.
H.RESOLUTION
Adjusts the horizontal size by increasing or decreasing the setting.
Press “Right” button to expand the width of the image on the screen.
Press “Left” button to narrow the width of the image on the screen.
*1 MDview 232/241 only.
*2 This item will not be reset by FACTORY PRESET (Tag7).
