manualshive.com logo in svg

NEC EXP704, Maintenance Manual, Page: 65 / 198

Share
Download
NEC EXP704 Maintenance Manual Download Page 65

1. System BIOS 

 

Express5800/E120g-M  Maintenance Guide 

65

Chapter 2  Useful Features 

(a)  PCI Device Controller and Option ROM Settings submenu 

The following screen appears when 

UEFI

 is selected for 

Boot Mode

 in Boot menu. 

On this menu, you cannot select 

VGA Priority

 option. If you want to specify 

VGA Priority

, change 

Boot Mode

 

to Legacy in Boot menu. 

 

 

For details about the options, see the table below. 

Option Parameter 

Descriptions 

VGA Controller 

Disabled 
[Enabled] 

Enable or disable the onboard VGA controller. 
This option is automatically set to 

Enabled

 if 

only the onboard VGA controller is valid and 
Serial Redirection is disabled. 

VGA Priority   

[Onboard]  

Offboard 

Specify priority to expand ROM of VGA 
controller.. 

LAN Controller 

Disabled 
[Enabled] 

Enable or disable the onboard LAN controller. 

This option is fixed to 

Enabled

 if 

Shared LAN

 

is enabled in Off-line Tools. 

LAN1 Option ROM Scan 

Disabled 
[Enabled] 

Enable or disable the option ROM SCAN for 
onboard LAN 1. 

LAN2 Option ROM Scan 

Disabled 
[Enabled] 

Enable or disable the option ROM SCAN for 
onboard LAN 2. 

LAN3 Option ROM Scan 

Disabled 
[Enabled] 

Enable or disable the option ROM SCAN for 
onboard LAN 3. 

LAN4 Option ROM Scan 

Disabled 
[Enabled] 

Enable or disable the option ROM SCAN for 
onboard LAN 4. 

PCI1 Slot Option ROM 

Disabled 
[Enabled] 

Enable or disable the option ROM on PCI slot. 
1. 

PCI2 Slot Option ROM 

[Disabled] 
Enabled 

Enable or disable the option ROM on PCI slot. 
2. 

 

 

[    ]:  Factory setting 

 

Note 

For a RAID Controller, LAN card (network boot), or Fibre Channel controller, if no 
Hard Disk Drive on which an OS is installed is connected, set the option ROM for 
that slot to 

Disabled

. 

Summary of Contents for EXP704







































































































































































































Reviews:

No comments