manualshive.com logo in svg

NEC EXP704, Maintenance Manual, Page: 167 / 198

Share
Download
NEC EXP704 Maintenance Manual Download Page 167

1. POST Error Message 

 

Express5800/E120g-M  Maintenance Guide 

167

Chapter 3  Appendix 

(1) 

Error messages 

 

Error Message 

Cause 

Action 

8000 

System variable is 

corrupted. 

Illegal setup information of BIOS was 
detected. 

Run BIOS Setup Utility (SETUP), and then 
select 

Load Setup Defaults

 and specify 

the necessary settings. 

8001 

Real time clock error 

Real time clock error was detected. 

Run SETUP, and then specify the correct 
date and time.   

8002 Check 

date and time settings 

Incorrect date and time set on real 
time clock was detected. 

8003 

System battery is dead - 

Replace and run SETUP 

The battery for storing system settings 
is dead. 

Contact your sales representative.   
After the replacement, run SETUP, and 
then specify the correct settings. 

8005 

Previous boot incomplete - 

Default configuration used 

The previous POST processing did 
not finish. 

Use SETUP to specify the correct settings. 

8006 System 

configuration 

data 

cleared by Jumper. 

SETUP settings were cleared by the 
jumper. 

Follow the steps described in 

Chapter 1 (7. 

Resetting and Clearing the Server). 

Run SETUP, and then setup each item 
again.  
This error message also appears when 
lithium battery is removed. 

8007 SETUP 

Menu Password cleared 

by Jumper. 

The password for SETUP was cleared 
by the jumper. 

8020 

BIOS update error. 

BIOS update failed. 

Try BIOS update again.   

8021 

Recovery jumper is set, but 

recovery images is not 

found. 

Recovery jumper is set, but recovery 
image is not found. 

Contact your sales representative. 
 

8800 DXE_NB_ERROR 

An error was detected during 
initialization of chipset. 

8801 DXE_NO_CON_IN 

An error was detected during 
initialization of console. 

8802 DXE_NO_CON_OUT 

8803 PEI_DXE_CORE_NOT_FOUND 

A flash ROM for system is corrupt. 

8804 PEI_DXEIPL_NOT_FOUND 

8805 DXE_ARCH_PROTOCOL_NOT_AVA

ILABLE 

8806 PEI_RESET_NOT_AVAILABLE 

The system was not reset correctly. 

8807 DXE_RESET_NOT_AVAILABLE 

8808 DXE_FLASH_UPDATE_FAILED 

A flash ROM for system was not 
written to correctly. 

8830 PEI_RECOVERY_NO_CAPSULE 

A flash ROM for system was not 
recovered correctly. 

8831 PEI_RECOVERY_PPI_NOT_FOUN

D 

8832 PEI_RECOVERY_FAILED 

9000 Unsupported 

CPU 

detected 

An unsupported CPU was detected. 

9001 Unsupported 

CPU detected on 

CPU #1 

9002 Unsupported 

CPU detected on 

CPU #2 

9021 Unsupported 

CPU 

Speed 

detected on CPU #1 

A CPU of which clock speed is 
unsupported was detected. 

9022 Unsupported 

CPU 

Speed 

detected on CPU #2 

9040 PEI_CPU_SELF_TEST_FAILED 

An error was detected in CPU 
initialization. 

9041 Detected 

CPU Error on CPU #1 

An error was detected on CPU #1. 

9042 Detected 

CPU Error on CPU #2 

An error was detected on CPU #2. 

9060 PEI_CPU_MISMATCH 

CPU #1 and #2 are not the same type. 

9080 

Link in Slow Speed Made 

between CPU1 and CPU2. 

Low-speed mode was detected on bus 
between CPU1 and CPU2. 

9081 

Link Failure between CPU1 

and CPU2 

Connection failure was detected on 
bus between CPU1 and CPU2. 

Summary of Contents for EXP704







































































































































































































Reviews:

No comments