background image

1. System BIOS 

 

Express5800/E120g-M  Maintenance Guide 

62

Chapter 2  Useful Features 

(2) Memory 

Configuration 

submenu 

From the 

Advanced

 menu, select 

Memory Configuration

 and then press the <Enter> key to display the menu 

screen shown below. For the menu that has    on the left, move the cursor to it and then press the <Enter> key 
to show its submenus. 

 

 
For details about the options, see the table below. 

Option Parameter 

Descriptions 

Memory Information 

 

 

Hardware Memory Test 

[Disabled] 
Enabled 

Enable or disable to execute memory test 
during POST. 
If a memory error is detected while this option 
is set to 

Enabled

, the relevant memory 

resource is degraded. 

Memory Retest 

[No] 
Yes 

When this option is set to 

Yes

, error 

information on memory is cleared, and all 
DIMMs are reconfigured at the next startup. 

No

 is automatically selected after DIMMs are 

reconfigured. 

Memory Frequency Limit 

[Auto] 
1333 MHz 
1600 MHz 
1866 MHz 
2133 MHz 
2400 MHz 

Specify the upper limit of operating frequency 
of memory. The operating frequency may be 
lowered than the specified value depending on 
memory configuration. 

NUMA 

Disabled 
[Enabled] 

Enable or disable Non-Uniform Memory 
Access feature. This option is displayed only 
in multi-processor configuration.. 

Cluster On Die

 

[Disabled] 
Enabled 
 

Enables or disables Cluster On Die feature. 
This option is accessible when the installed 
processor supports this feature and 

Enabled 

is specified for 

NUMA

This option must be disabled on VMware ESXi 
5.x. 

Snoop Mode

 

Home Snoop 
[Early Snoop] 
Home Snoop with 
Directory 

Specify Snoop mode. This option is accessible 
when 

Disabled 

is specified for 

Cluster on 

Die

.

 

Patrol Scrub 

Disabled  
[Enabled] 

Enable or disable memory RAS feature (Patrol 
Scrubbing). 

Demand Scrub 

Disabled 
[Enabled] 

Enable or disable memory RAS feature 
(Demand Scrubbing). 

 

 

[    ]:  Factory setting 

Summary of Contents for EXP704







































































































































































































Reviews: